Pach and Company AeGIS NPB7000 Series Quick Guide - Manual

Page 1
 Missing Parts, contact Pach and Company 1-888-678-7224
 Defective system under manufacturer warranty,
call 1-888-678-7224 for advance replacement
 24 Months warranty for complete system

6 Months warranty for Printed Circuit Board
What is Master Code: 4- digit code to log-on to programming
mode (0000 is default)
What is Dir (directory code): 2, 3, or 4 digit number see function
code 09. The number can be associated to apartment no., first
three digit of phone no., last four digit of phone no. , or any random
no. assigned to each tenants. Every tenant must have different
directory code no..
What is Access Code: 4-digit code for tenant to open the door or
gate.
Exit program, clear field,
reset keystroke. 46 Display system’s
information
Save program 50
Clear memory to factory
default
00
Change master code
(0000 is default)
51
Enable No Phone Bill
Must be set to 1
01
Add new tenant
Tenant’s phone
number is 4-digit relay
number (i.e. 0001, 0002)
70 Change talk time (010-
180 seconds) 60
seconds is default
02 Edit existing tenant
71 Change door open
interval (04-99 seconds)
03 Delete existing tenant 72
Invalid code lock-out
count (1-9). 3 is default
04 Clear all tenants 73
Tone/pulse dialing.
Tone is default
05
Manual unlock/lock relay 1
with timer (01-98 hours, 99
hours unlock hold, 00
hours to lock)
74
Enable/disable auto
answer. Enable is
default
06
Directory Digit
Select 2, 3 or 4 digit
default= 3 digit
75
Enable/disable keypad
press beep. Enable is
default
07
Single or multi system
(single is default)
76
Enable/disable speaker
beep. Enable is default
08 System ID number (n/a) 77
PBX enable. Not
applicable
10 Edit scrolling message 78
View name and
directory
40 Master code mask.
Warning: Master code
cannot be recovered if
masked. Board must be
replaced. 91
Total number of tenant.
Tenant with no name
will not be included
Log on to programming: Press
simultaneously then release, the
welcome message will stop scrolling
(repeat if screen still scrolls) enter 4-digit
“
MASTER CODE ” (0000 is default), the
screen will show:
Select the “ Function Code ” from the table
Two ways call from the system
1. Press to scroll name from A-Z or to scroll name
from Z-A then press to call name selected.
2. Press wait for tone then press the directory no.
Opening the door remotely press
Opening the door using the access code press
(display screen will stop scrolling) then press a valid 4-digit
access code.
Extending talk time tenant must press from the phone
after the time out warning beep.
Call waiting feature :
1. Press 0 to transfer between two calls or to answer the
second call
2. Press 0 again to return to the original call
Doorman phone :
1. Press 0 to transfer between two calls or to answer the
second call
2. Press 0 again to return to the original call
Make an outside call from Doorman phone :
1. Press 0, wait for dial tone, then dial the phone number
HOW TO ENTER A CHARACTER
1. Press the associated button to enter a character then
2. Press
3. You have 30 seconds to enter each letter or character.
4. Letter QZ, numeric 0-9 and punctuations press
5. Press space and for backspace
PACH AND CO 1-888-678-7224 Quick Guide
Technical Support 1-888-678-7224
Mon-Fri 7:30 am -3:30pm Pacific Standard Time
WARNING:
DO NOT USE ON BOARD
12VDC and GND TO POWER A DOOR STRIKE
OR MAGNETIC LOCK
SEPARATE POWER MUST BE USED TO
POWER A DOOR STRIKE OR MAGNETIC
LOCK.