PERKO 0946 - Manual

MOUNTING TEMPLATE
The above lights are designed for use on sail or power driven
vessels under 20 meters (65.6 ft.) in length operating on a
nominal 12 volt or 32 volt system. In order to comply with the
‘72 COLREGS and the U.S. Inland Rules, the following must
be adhered to:
MOUNTING INFORMATION
Read all instructions before proceeding
1). These Instructions show the orientation of the light after the proper location has been deter-
mined. For proper light selection, positioning and configuration, refer to A.B.Y.C. Standard
A-16* the ‘72 COLREGS* and the U.S. Inland Navigation Rules.
2). These lights are supplied with the proper bulb for operation on a nominal 12 volt system or
a nominal 32 volt system. Use PERKO Cat. No. 0070DP0CLR, 12V, 10W bulb for a 12 volt
system (Cat. No. 094600112V and 09460DP112V Stern Light). Use PERKO Cat. No.
0070DP2CLR bulb for a 32 volt system (Cat. No. 0946DP332V Stem Light). NOTE: PERKO
Series 0946 used with a 32W bulb is not certified in accordance with 33 CFR 183.810 as this light
is intended for replacement use only on appropriate vessels constructed prior to 11/1/03. All
previous certifications apply.
3). These lights are designed to be mounted on a vertical surface that is perpendicular to the
centerline of the boat and facing astern.
4). Draw a 6 inch long horizontal reference line through the center of the selected mounting
location.
5). Cut out the mounting template below, Tape it on the mounting surface such that the refer-
ence line (drawn above) passes through the exact center of the template.
6). Drill two holes through the template as indicated for the #6 mounting screws.
7). Drill a 2-1/8 inch hole to accommodate socket holder as indicated.
8). Attach supply connections to the light, making sure to wire in accordance with both A.B.Y.C.
Standard E-9* and U.S. Coast Guard Safety Standards for Boat Electrical Systems (33
CFR 183).
9). Attach the light to mounting surface using #6 screws, noting that the lens is marked “up”
and “down” for proper orientation (see template).
* The above referenced standards can be obtained from:
(1). American Boat & Yacht Council, Inc. (2). U.S. Coast Guard
613 Thired Street, Suite 10 Washington, D.C. 20593
Annapolis, MD 21403 (or your local C.G. office)
PERKO, INC.
16490 N.W. 13th Avenue
0946INS1
Miami, FL 33169-5707 12/08
www.perko.com
CAT. NOS.
094600112V
0946DP112V
0946DP332V
0946001WHT
0946DP1WHT
0946DP3WHT
USCG APPROVAL
33 CFR 183.810
Visibility: 2nm
Tested By: IMANNA Labs.
Date: 2/4/03
Meets ABYC A-16
Cat. No. 0946 Series
Stern Lights
MOUNTING TEMPLATE
The above lights are designed for use on sail or power driven
vessels under 20 meters (65.6 ft.) in length operating on a
nominal 12 volt or 32 volt system. In order to comply with the
‘72 COLREGS and the U.S. Inland Rules, the following must
be adhered to:
MOUNTING INFORMATION
Read all instructions before proceeding
1). These Instructions show the orientation of the light after the proper location has been deter-
mined. For proper light selection, positioning and configuration, refer to A.B.Y.C. Standard
A-16* the ‘72 COLREGS* and the U.S. Inland Navigation Rules.
2). These lights are supplied with the proper bulb for operation on a nominal 12 volt system or
a nominal 32 volt system. Use PERKO Cat. No. 0070DP0CLR, 12V, 10W bulb for a 12 volt
system (Cat. No. 094600112V and 09460DP112V Stern Light). Use PERKO Cat. No.
0070DP2CLR bulb for a 32 volt system (Cat. No. 0946DP332V Stem Light). NOTE: PERKO
Series 0946 used with a 32W bulb is not certified in accordance with 33 CFR 183.810 as this light
is intended for replacement use only on appropriate vessels constructed prior to 11/1/03. All
previous certifications apply.
3). These lights are designed to be mounted on a vertical surface that is perpendicular to the
centerline of the boat and facing astern.
4). Draw a 6 inch long horizontal reference line through the center of the selected mounting
location.
5). Cut out the mounting template below, Tape it on the mounting surface such that the refer-
ence line (drawn above) passes through the exact center of the template.
6). Drill two holes through the template as indicated for the #6 mounting screws.
7). Drill a 2-1/8 inch hole to accommodate socket holder as indicated.
8). Attach supply connections to the light, making sure to wire in accordance with both A.B.Y.C.
Standard E-9* and U.S. Coast Guard Safety Standards for Boat Electrical Systems (33
CFR 183).
9). Attach the light to mounting surface using #6 screws, noting that the lens is marked “up”
and “down” for proper orientation (see template).
* The above referenced standards can be obtained from:
(1). American Boat & Yacht Council, Inc. (2). U.S. Coast Guard
613 Thired Street, Suite 10 Washington, D.C. 20593
Annapolis, MD 21403 (or your local C.G. office)
PERKO, INC.
16490 N.W. 13th Avenue
0946INS1
Miami, FL 33169-5707 12/08
www.perko.com
CAT. NOS.
094600112V
0946DP112V
0946DP332V
0946001WHT
0946DP1WHT
0946DP3WHT
USCG APPROVAL
33 CFR 183.810
Visibility: 2nm
Tested By: IMANNA Labs.
Date: 2/4/03
Meets ABYC A-16
Cat. No. 0946 Series
Stern Lights