PERKO 0607 User Manual
Mounting template
Fig. Nos. 0606 & 0607 Series L.E.D. Utility Light
The above lights are not designed for navigational use.
MOUNTING INFORMATION
Read all instructions before proceeding.
MOUNTING TEMPLATE
1). These instructions show the orientation of the light after the proper
mounting location has been determined.
2). These lights are supplied with the proper circuit for operation on a
nominal 12 volt system.
3). These lights contain no user serviceable components.
4). Draw a 8-1/2 inch long reference line through the center of the select-
ed mounting location.
5). Cut out the mounting template below.Tape it on the mounting surface
such that the reference line (drawn above) passes through the exact
center of the template.
6). Drill four holes through the template as indicated for the #6 mounting
screws and two or three holes 3/32” to 1/8” diameter to accommodate
the wiring as indicated on template.
7). Wiring should be done by a qualified marine electrician. Attach
supply connections to the light, making sure to wire in accordance with
both A.B.Y.C. Standard E-9* and U.S. Coast Guard Safety Standards
for Boat Electrical Systems (33CFR 183)* Observe polarity.
8). Attach the light to the mounting surface using #6 mounting screws.
* The above referenced standards can be obtained from:
(1). American Boat & Yacht Council, Inc.
613 Third Street, Suite 10
Annapollis, MD 21403
(2). U.S. Coast Guard
Washington, D.C. 20593
(or your local C.G. office)
Perko, Inc.
16490 N.W. 13th Avenue
Miami, FL. 33169-5707
www.perko.com
03/09
0606INS1
Cut out Template on Dotted Line
Ê
This is a 3/4”
circle in order
to scale internet
printed
templates
Fig. Nos. 0606 & 0607 Series L.E.D. Utility Light
The above lights are not designed for navigational use.
MOUNTING INFORMATION
Read all instructions before proceeding.
MOUNTING TEMPLATE
1). These instructions show the orientation of the light after the proper
mounting location has been determined.
2). These lights are supplied with the proper circuit for operation on a
nominal 12 volt system.
3). These lights contain no user serviceable components.
4). Draw a 8-1/2 inch long reference line through the center of the select-
ed mounting location.
5). Cut out the mounting template below.Tape it on the mounting surface
such that the reference line (drawn above) passes through the exact
center of the template.
6). Drill four holes through the template as indicated for the #6 mounting
screws and two or three holes 3/32” to 1/8” diameter to accommodate
the wiring as indicated on template.
7). Wiring should be done by a qualified marine electrician. Attach
supply connections to the light, making sure to wire in accordance with
both A.B.Y.C. Standard E-9* and U.S. Coast Guard Safety Standards
for Boat Electrical Systems (33CFR 183)* Observe polarity.
8). Attach the light to the mounting surface using #6 mounting screws.
* The above referenced standards can be obtained from:
(1). American Boat & Yacht Council, Inc.
613 Third Street, Suite 10
Annapollis, MD 21403
(2). U.S. Coast Guard
Washington, D.C. 20593
(or your local C.G. office)
Perko, Inc.
16490 N.W. 13th Avenue
Miami, FL. 33169-5707
www.perko.com
03/09
0606INS1
Cut out Template on Dotted Line
Ê
This is a 3/4”
circle in order
to scale internet
printed
templates
Drill 3/32” to 1/8” Dia. holes for electric wires (2) or (3) places
Drill for #6 Screws (4) places
Drill 3/32” to 1/8” Dia. holes for electric wires (2) or (3) places
Drill for #6 Screws (4) places