PERKO 1418 - Manual

PERKO, INC.
16490 N.W. 13th Avenue
Miami, FL 33169-5707
www.perko.com
Cat. Nos. 1418 Series Sealed EPA Fill
Installation and Operation Instructions
These fills meet the new CARB and EPA requirements of U.S.C.G. Safety Standards (July 31, 2011)
for 40 CFR Parts 9, 60, 80 et al. Control of Diurnal Emissions From Nonroad Spark-Ignition Engines
and Equipment.
WARNING Do not attempt to use these non-vented EPA fills on older vented non-EPA certified boats.
Although similar in appearance, the cap on this fill is not vented whilst the cap on the older
version is vented. The vent line attached to this body functions only with the cap open and
during the filling process.
1. Select mounting location:
- In accordance with A.B.Y.C., U.S. Coast Guard and E.P.A. requirements and regulations.
- Surface must be flat and provide adequate clearance to remove the cap.
- Allow for adequate clearance under fill for routing fill and vent hose, which must be selected and installed in
accordance with A.B.Y.C. requirements and U.S. Coast Guard Safety Standards for Small Boat Fuel Systems
(33 CFR 183).
2. Non-metallic fills do not need to be grounded or bonded.
3. Attach mounting template to selected mounting surface and orient for desired position of fill/vent connections and
for ease of insertion of the fuel nozzle into the neck. Drill where indicated, drilling the 3/4 inch hole first.
NOTE: The 2-1/16” dimension of the larger hole is sized to provide mounting surface support to fill the
body. DO NOT use larger size cutter or drill.
4. Mount fill using #10 Round head or Pan head screws. Caulk if necessary.
5. Attach and clamp fill and vent hoses, also in accordance with the above referenced requirements.
(1). American Boat & Yacht Council, Inc. (2). U.S. Coast Guard (3). E.P.A.
613 Third Street, Suite 10 Washington, D.C. 20593 401 “M” Street S.W.
Annapolis, MD 21403 (or you local C.G. office) Washington, D.C. 20460
04/11
1418INS1
Drill for #10 Screws (4)
Drill 3/4” Dia. Hole
(Drill First )
2-1/16” Dia.
(Drill Second)
Hing
e Side
1-7/32”
MOUNTING TEMPLATE
PERKO, INC.
16490 N.W. 13th Avenue
Miami, FL 33169-5707
www.perko.com
Cat. Nos. 1418 Series Sealed EPA Fill
Installation and Operation Instructions
These fills meet the new CARB and EPA requirements of U.S.C.G. Safety Standards (July 31, 2011)
for 40 CFR Parts 9, 60, 80 et al. Control of Diurnal Emissions From Nonroad Spark-Ignition Engines
and Equipment.
WARNING Do not attempt to use these non-vented EPA fills on older vented non-EPA certified boats.
Although similar in appearance, the cap on this fill is not vented whilst the cap on the older
version is vented. The vent line attached to this body functions only with the cap open and
during the filling process.
1. Select mounting location:
- In accordance with A.B.Y.C., U.S. Coast Guard and E.P.A. requirements and regulations.
- Surface must be flat and provide adequate clearance to remove the cap.
- Allow for adequate clearance under fill for routing fill and vent hose, which must be selected and installed in
accordance with A.B.Y.C. requirements and U.S. Coast Guard Safety Standards for Small Boat Fuel Systems
(33 CFR 183).
2. Non-metallic fills do not need to be grounded or bonded.
3. Attach mounting template to selected mounting surface and orient for desired position of fill/vent connections and
for ease of insertion of the fuel nozzle into the neck. Drill where indicated, drilling the 3/4 inch hole first.
NOTE: The 2-1/16” dimension of the larger hole is sized to provide mounting surface support to fill the
body. DO NOT use larger size cutter or drill.
4. Mount fill using #10 Round head or Pan head screws. Caulk if necessary.
5. Attach and clamp fill and vent hoses, also in accordance with the above referenced requirements.
(1). American Boat & Yacht Council, Inc. (2). U.S. Coast Guard (3). E.P.A.
613 Third Street, Suite 10 Washington, D.C. 20593 401 “M” Street S.W.
Annapolis, MD 21403 (or you local C.G. office) Washington, D.C. 20460
04/11
1418INS1
Drill for #10 Screws (4)
Drill 3/4” Dia. Hole
(Drill First )
2-1/16” Dia.
(Drill Second)
Hing
e Side
1-7/32”
MOUNTING TEMPLATE