Perma Pure Baldwin-Series 10410 - Manual (Page 34)

2. Multi-Channel Mounting
Flat bladed screwdriver required for mounting.
Tubing loading key required for mounting.
Note: Other special mounting hardware for multi-channel pumping.
See “ 3. Replacement Parts and Accessories”.
a) Load the pump heads with tubing.
b) Install the four correct length-mounting screws in drive.
c) Slide the first pump head into the mounting screws.
d) Place key in slot on mounting shaft. Twist to align tang on rotor
shaft with slot in motor drive shaft. Shift the pump housing
around till it drops over the alignment pins (if present).
e) Repeat for each additional pump head, aligning pump head tang
with slot on previously mounted pump head.
f) Slide the four flat washers onto screws and secure with the four
wingnuts. Tighten with fingers only.
g) A support bracket is supplied with 3 and 4 channel mounting
hardware for additional support. Mount over bottom two screws.
Inert one of the three different adjustments screws depending
upon drive height.
3. Replacement Parts and Accessories
A. End Bells (order two end bells for a complete head assembly).
Pump Head # PC Order number Pump Head # PC Order
number
07013-00, -20
07013-10, -21 MN-07013-81
MN-07013-91 -
07013-50, -52
-
MN-07013-92
07014-00, -20
07014-10, -21 MN-07014-81
MN-07014-91 -
07014-50, -52
-
MN-07014-92
07015-00, -20
07015-10, -21 MN-07015-81
MN-07015-91 -
07015-50, -52
-
MN-07015-92
07016-00, -20
07016-10, -21 MN-07016-81
MN-07016-91 -
07016-50, -52
-
MN-07016-92
07017-00, -20
07017-10, -21
MN-07017-81
MN-07017-91
-
07017-50, -52
-
MN-07017-92
07018-00, -20
07018-10, -21 MN-07018-81
MN-07018-91 -
07018-50, -52
-
MN-07018-92
07024-00, -20
07024-10, -21
MN-07024-81
MN-07024-91
-
07024-50, -52
-
MN-07024-92
07035-02, -20
07035-12, -21 MN-07035-81
MN-07035-91 -
- -
-
B. Rotor assemblies
Pump Head number Pump Head suffix Order number
07013, 07014, 07016
07018
-00
-10, -50
-20
-21, -52 MN-07013-75
MN-07013-76
MN-07013-80
MN-07013-95
07015, 07024, 07035
-00, -02
-10, -50, -12
-20
-21, -52 MN-07013-75
MN-07013-76
MN-07013-80
MN-07013-90
C. MN-07021-04 Thrust washers. Pack of 10.
D. MN-07013-90 Tubing loading key.
E. Mounting hardware for standard pump heads
.
Set contains four #8-32 screws, four washers, and four wingnuts.
Number of heads
To be mounted
Cold- rolled steel
Order number
Stainless steel
Order number
1
2
3
4 MN-07013-02
MN-07013-03
MN-07013-03
MN-07013-07 MN-07013-04
MN-07013-05
MN-07013-08
MN-07013-09
4. Specifications
Thin wall* Thick wall*
Maximum continuous
discharge pressure-psi(bar):
20(1.4) 25(1.7)
Maximum intermittent
discharge pressure-psi(bar):
35(2.4) 40(2.7)
Maximum vacuum: 660(510’)m Hg 26(20’)in Hg
Maximum suction lift: 8.8(6.7’)m H2O 29(22’)ft H2O
Number of rollers:
3
Occlusion: Standard fixed
Maximum pump speed (rpm): 600
Nominal torque load: 6.5 kg-cm(90 oz-in)
Housing materials: Polycarbonate (PC) all models, or Polyphenylene
sulfide (PPS) all models except 07035
Roller/rotor materials: Cold rolled Stl (CRS) or Stainless Stl (SS)
Operating temperature:
0 to 40° (32 to 104°F)
*Thin wall: tubing 13, 14, 16, 17, 18 Thick wall: tubing 15, 24, 35
ɈWith tubing 17 & 18
ū Use in this temperature range for continuous duty operation with no
decrease in performance or product life. Pump heads will work outside
this range with some possible reductions in performance or product
life.
5. Warranty and Return Items
Warranty
Use only MASTERFLEX Precision Tubing with MASTERFLEX Pumps
to insure optimum performance. Use of other tubing may void
applicable warranties.
The manufacturer warrants this product to be free from any significant
deviations from published specifications. If repair or adjustment is
necessary within the warranty period, the problem will be corrected at
no charge if it is not due to misuse or abuse on your part, as determined
by the manufacturer. Repair costs outside the warranty period, or those
resulting from product misuse or abuse, may be invoiced to you.
The warranty period for this product is noted on the Warranty Card.
Product Return
To limit charges and delays, contact the seller or manufacturer for
authorization and shipping instructions before returning the product,
either within or outside the warranty period. When returning the
product, please state the reason for the return. For your protection, pack
the product carefully and insure it against possible damage or loss. Any
damages resulting from improper packaging are your responsibility.
Technical Assistance
If you have any questions about the use of this product, contact the
manufacturer or authorized dealer.