PROLiNK PRO1301WE Quick Installation Guide - Manual

Mobile Monitor Overview Application Supported
Figure: Digital Video and USB
power cable
Figure: Front View of PRO1301WE Figure: Rear View of PRO1301WE
Digital Camera, Video Player, Smart Phones,
Gaming Consoles or other products that
support of Digital Video Output (DVI) are
compatible with the PRO1301WE.
Note: Actual result depends on the product
Video signal output format and its operation
mode; not all products are compatible with
full screen display on the Mobile Monitor.
IMPORTANT
※Keep the laptop away from the table edge to prevent it from falling off the table. ※The cable may be damaged if you pull it
out by force. ※To disconnect power cable connector
from the Mobile Monitor, please push the
connector
towards right
hand side as
illustration
shown.
※Use the laptop and monitor on a flat surface. Otherwise, the laptop and monitor may topple; if the monitor is rotated to a position behind the laptop monitor, it may cause the laptop to
fall backwards. Turning the Mobile Monitor to an angle between 0° and 180° is not recommended.
※Do not install the Mobile Monitor on moving objects, such as window of a vehicle; the monitor may fall off when moving.
※Do not install the Mobile Monitor on walls, doors, signage, bathrooms, ceilings and other dangerous places, and do not drop the Mobile Monitor during installation to prevent it from
injuring human bodies.
※Do not flip open the Mobile Monitor to a horizontal position first, and avoid knocking against objects on the table while opening your laptop.
※Place the monitor into a bag with protective function for carrying, and avoid knocking against objects in the bag to prevent damaging the screen.
※PRO1301WE only reads the DVI Digital Video signal, support HDCP but does not support the full HDMI interface.
※PRO1301WE does not have speakers, thus it is not audio supported.
※This product is not waterproof. Do not use it near water or in wet environment.
※Do not insert any object into the Product’s slots or gaps.
※The shortcut keys are the capacitive sensing buttons, which is sensitive by gentle touching. Do not press hard or press fast continuously. Repeatedly pressing the button may cause the
button slow in response. For continuous adjustment of "Increase/Up" or "Decrease/Down", press and hold the corresponding button for automatic and continuous Increase / Decrease.
※Please visit www.prolink2u.com to download the Mobile Monitor user manual.
Installation Instructions - Horizontal Display
1
Install Digital Video and USB-Powered cable
If you wish to use the HDMI port on the laptop, please use Digital
Video and USB-Powered Cable. If you wish to use the D-sub (VGA) or
mini-Display Port on the laptop, please purchase the Analog Video
and USB-Powered Cable or mini-Display Port and USB-Powered
Cable.
Connect the Video and Power connector to PRO1301WE Video port,
(1) Insert the latch into the groove of the Video power connector.
(2) Slide the Video power connector toward the left for a proper
connection. [Warning: Not inserting the latch into the groove may
result in damaging the connector. Please check the Video power
connector is properly connected and not protruding out. If
protrusion occurs, the connection might not be properly connected
and monitor will not be able to operate.]
1-1
Insert the latch into the groove of the
Video power connector of the PRO1301WE
2
Connect the PRO1301WE to the laptop
Connect the USB power connector to the laptop's USB port, and
then connect the Digital Video connector to the laptop's HDMI
Video output port
3
Adjust the laptop and monitor extension setting
After switching on the laptop, go to “Control Panel” of Windows
operating system to proceed with monitor extension setting.
If you use Windows 7,
Select “2.DVI LCD” (Digital Video) or “2. Display device: VGA” (Analog
Video) for Display.
Select “1366x768” for Resolution
Select "Landscape" for Orientation Select "Extend these displays" for
Multiple displays, and drag Display 2 to the right side of Display 1.
4
Switch on the laptop
Switch on the laptop’s monitor and press the power button of the
PRO1301WE
;
Adjust the brightness: press to adjust the monitor brighter
and press to adjust the monitor dimmer
※Note: The unavailability of “Duplicate these displays” or “Extend these
displays” on the laptop may be due to:
i) limitation of the laptop’s graphic card
ii) power saving mode of the laptop
iii) graphics card driver was not updated
Please seek for technical support from your laptop manufacturer or
graphics chip maker.
Installation Instructions – Vertical Display
1
Install the Video and USB-Powered cable
If you wish to use the HDMI port on the laptop, please use Digital Video and
USB-Powered Cable. If you wish to use the D-sub (VGA) or mini-Display Port on the
laptop, please purchase the Analog Video and USB-Powered Cable or mini Display Port
and USB-Powered Cable. Connect the Video and Power connector to PRO1301WE
Video port, (1) Insert the latch into the groove of the Video power connector. (2) Slide
the Video power connector toward the left for a proper connection. [Warning: Not
inserting the latch into the groove may result in damage to connector. Please check the
Video power connector is properly connected and not protruding out. If protrusion
occurs, the connection might not be properly connected and monitor will not be able to
operate.]Refer to Fig. 1-1 "Horizontal Display"
2
Connect the PRO1301WE to the laptop
Connect the USB power connector to the laptop's USB port, and then connect the Digital Video
connector to the laptop's HDMI Video output port.
Note: Place Mobile Monitor to the right side for better
view.
3
Adjust the laptop and monitor extension setting
After switching on the laptop, go to Windows’ “Control Panel” to make the
monitor extension setting.
If you are using Windows 7:
Select “2.DVI LCD” (Digital Video) or
“2. display device: VGA” (Analog Video) for Display
Select “1366x768” for Resolution
Select "Portrait (flipped)" for Orientation
Select "Extend these displays" for Multiple displays, and drag Display 2 to the
right side of Display 1.
4
Switch on the laptop
Switch on the laptop’s monitor and press the power
button
of the PRO1301WE; Adjust the
brightness: press to adjust the monitor
brighter and press to adjust the monitor
dimmer
※Note: The unavailability of “Portrait (flipped)” on the
laptop may be due to:
i) limitation of the laptop’s graphic card
ii) power saving mode of the laptop
iii) graphics card driver was not updated
I Please seek for technical support from your laptop
manufacturer or graphics chip maker.
Front Back
Holder Plate
Figure: Analog Video and
USB power cable (optional)