Reese 45299 TITAN RECEIVER - Manual

Installation Instructions
Dodge 2500/3500 Pickup
Part Numbers:
45299
Hitch Shown In Proper Position
Equipment Required: WOOD BLOCKS
Drill Bits: 9/16”
Wrenches: m16,m18,m21, 3/8”
Tighten M12 hitch fasteners with torque wrench to 75 Lb.-Ft. (102 N*M)
© 2010, 2011 Cequent Performance Products
Sheet 1 of 6 45299N 12-9-11 Rev. B
j
Qty. (4) HEX NUT – M14 X 2.00 o
Qty. (2) BLOCK – 1-1/2 X 3-1/2 X 1/4”
k
Qty. (4) CONICAL WASHER – 5/8” p
Qty. (4) HEX NUT – ½-13 GR 2H
l
Qty. (6) HEX NUT – M12 X 1.75
q
Qty. (2) FISH WIRE – 1/2”
m
Qty. (14) CONICAL WASHER – 1/2” r
Qty. (4) HEX BOLT – M12 X 1.75 X 45mm CL 10.9
n
Qty. (4) CARRIAGE BOLT – 1/2”-13 X 1-3/4” GR 8
10 Qty. (3) BLOCK – SPACER 1/2 X 1-1/2 X 5-3/4
Tighten M14 and 1/2” fasteners with torque wrench to 100 Lb.-Ft. (136 N*M)
Fastener Kit: 45299F
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to prevent entry
of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working beneath a vehicle and
wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE
J684.
Do Not Exceed Lower of Towing Vehicle
Manufacturer’s Rating or
Hitch type
Max Gross
Trailer WT (LB)
Max Tongue
WT (LB)
Weight Distributing 18000 (8172 kg) 2500 (1135 kg)
Weight Carrying
Ball Mount
18000 (8172kg) 2000 (908 kg)
Wiring Access Location: PU3, PU4
Form: F205 Rev A 5-6-05
EXISTING
M14 BOLTS
2010 MODEL
EXISTING
BUMPER
CORNER
BRACE
EXISTING
M12 BOLTS
EXISTING M14 HANDLE NUT (03-09 MODEL)
M14 FLANGED NUT (2010 MODEL)
LONG BED
FRAME
SHORT BED
FRAME
DRILL ONE HOLE
DRILL 2
HOLES
BED ATTACHMENT
HOLE
CENTER BUMPER
ATTACHMENT
BUMPER
ATTACHMENT
j k
l
m
n
p
o
m
Tighten M12 bed fasteners with torque wrench to 85 Lb.-Ft. (115 N*M)
Tighten all M10 fasteners with torque wrench to 42 Lb.-Ft. (57 N*M)
#3
#4
Bumper
FIGURE 1
NOTE;
WITH THIS HITCH INSTALLED
THE STEP BUMPER IS NO LONGER ABLE
TO BE USED AS A TOWING POINT.
!
03-09 MODEL
EXISTING
BUMPER
CORNER
BRACE
(NOT REQUIRED ON 03-09)
2010 – CURRENT
MODEL
ATTACHMENT
2003-09 MODEL
ATTACHMENT
TOP HOLE – BUMPER
ATTACHMENT
VIBRATION DAMPENER
(ON CERTAIN MODELS ONLY)
m
r
10
Must have pick-up chassis
Spring mount (as shown
above the frame).