Reese 36025 PREMIUM RECEIVER - Manual (Page 2)

DODGE (CONT.)
3. Push the hitch forward and center it on the frame. Tighten the rear nuts to hole it in place. Match drill four 1/2" holes for the front mounting
bolts. Insert four 1/2" carriage bolts with bolt plates down through the front holes. Install flat washers, lock washers, and nuts on the bolts.
See the diagram on the other side. Go to step 5.
FORD FLARESIDE WITH ROLLED PAN (NOT STEP BUMPER)
2. Clamp the hitch to the frame so the brackets clear the rolled pan
and so the rear mounting bolt hardware will fit in the front of the
crossmember. The large hole in the bracket will be about 2-1/2”
ahead of the rivet.
3. Match drill six 1/2" holes in the frame flange. Insert 1/2" bolts
with flat washers or bolt plates as shown.
4. Lower one side of the hitch enough to install a large spacer on
the rear bolt and two flat washers on the center bolt. Lift the hitch
and install flat washers, lock washers, and nuts on the bolts.
Repeat for the othe side. Go to step 5.
FORD BRONCO
2. Clamp the hitch to the frame so the brackets are as far rearward
as possible. Match drill six 1/2" ho les in the frame flange.
3. Screw one of the 1/2" carriage bolts onto the pull wire provided.
Thread a bolt plate over the bolt. Insert the end of the pull wire up
beside the gas tank and down through one of the drilled holes, a
small spacer, and the bracket. Repeat for the other 5 mounting holes.
Use two 1/2" flat washers instead of small spacers on the middle
mounting holes for both brackets. See the diagram to the right.
4. Install 1/2" flat washers, lock washers and nuts on all six mounting
bolts. Go to step 5.
GENERAL
5. Torque 1/2" hardware to 70 ft.*lb.
6. Reinstall the spare tire assembly. It may be necessary to trim
the lifting socket (pipe) on the Ford spare tire bracket assembly.
The spare tire bracket on the Dodge may need to be relocated.
FORD FLARESIDE
WITH ROLLED PAN
FRAME LINE
FRAME
SMALL SPACER
Reese warrants its Hitches, custom Hitch Receivers, and Sway Controls from date of purchase against defects in material and workmanship under normal use and
service, ordinary wear and excepted, for the ownership life of the original consumer purchaser. Reese will replace FREE OF CHARGE any part which proves defective in
material or workmanship when presented to any Reese dealer, Reese Warehouse or return to factory. TRANSPORTATION CHARGES PREPAID, at the address
below. THIS WARRANTY IS LIMITED TO DEFECTIVE PARTS REPLACEMENT ONLY. LABOR CHARGES AND/OR DAMAGE INCURRED IN INSTALLATION OR
REPLACEMENT AS WELL AS INCIDENTAL AND CONSEQUENTIAL DAMAGES CONNECTED THEREWITH ARE EXCLUDED. Some states do not allow the
exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. Any damage to the Hitch, Custom Hitch receiver
or Sway Control as a result of misuse, abuse, neglect, accident, improper installation, or any use violative of instructions furnished by us, WILL VOID THE WARRANTY.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. In the event of a problem
Reese warrants its Hitches, Custom Hitch Receivers and Sway Controls from date of purchase against defects in material and workmanship under normal use and
service, ordinary wear and tear excepted, for the ownership life of the original consumer purchaser.
with warranty service or performance, you may be able to go to a small claims court, a state court, or a federal district court.
LIMITED WARRANTY
THIS PRODUCT COMPLIES WITH SAFETY SPECIFICATION AND REQUIREMENTS FOR THE STATE OF NEW YORK AND VESC REGULATION V-5 FOR CONNECTING DEVICES AND
TOWING SYSTEMS. WEIGHT DISTRIBUTING HITCH RATING IS 12,000 LB. MAX. GROSS TRAILER WEIGHT AND 1200 LB. MAX. TONGUE WEIGHT. WEIGHT CARRYING HITCH RATING IS
7500 LB MAX GROSS TRAILER WEIGHT AND 750 LB MAX TONGUE WEIGHT. CONSULT VEHICLE OWNERS MANUAL FOR TOWING RECOMMENDATIONS AND LIMITATIONS.
Towing Products
PO Box 8102
47774 Anchor Ct.
Plymouth, MI 48170 Towing Products
2351 Winston Park Drive
Oakville, Ontario
Canada L6H6R7
36025IN-03/25/03E © 1995, 2003 REESE PRODUCTS, INC. Litho in USA