Reese 44011 PROFESSIONAL RECEIVER - Manual

Installation Instructions
Chevrolet Van
GMC Van
Part Numbers:
51003
44011
Hitch Shown In Proper Position
Equipment Required: Pull Wire (Provided)
Wrenches: 9/16 Socket & Wrench,
3/4 Socket & Wrench
Drill Bits: None
1 Existing 1/2 Hex Bolt & Washer
1. Remove the two lower bumper support brackets, one per side; Save the bolts and washers. Save the bracket and return to the owner.
2. Place the left and right side brackets against the frame bottom. Install four 1/2" bolts and washers removed in Step One. Leave the bolts loose.
3. Install two 3/8" bumper bolts (removed in Step One), two 3/8" serrated washers, and two 3/8" lock nuts (from the fasteners provided). Leave the
lock nuts loose at this time.
!WARNING! Two 3/8" lock nuts must be used with two 3/8" bumper bolts; otherwise the receiver could loosen and separate from the vehicle.
4. Screw the pull wire onto a 1/2" carriage bolt. Feed the pull wire through a block and the large hole in the outboard side of the frame.
Pull it out the bottom hole of the frame. Repeat for the other side. Install two 1/2" serrated washers, lock washers and nuts on the bolts. Leave
the nuts loose at this time.
5. Tighten bolts and nuts in the exact order listed; this allows the receiver to be pulled rearward to the bumper before the frame bolts are tightened.
Tighten all 3/8 fasteners with torque wrench to 30 Lb.-Ft. (41 N*M)
Tighten all 1/2 fasteners with torque wrench to 75 Lb.-Ft. (102 N*M)
Rev. B 6-27-06 44011IN Sheet 1 of 1 z 2002, 2004, 2006 Cequent Towing Products
Block Qty. (2) 4
Hex Nut 1/2-13 Qty. (2) 7 Carriage Bolt 1/2-13 X 2.00 Qty. (2) 3
Lock Washer 1/2 Qty. (2) 6 Hex Locknut 3/8-16 Qty. (2) 2
Conical Washer 1/2 Qty. (2) 5 Washer 3/8 Qty. (2) 1
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
Fastener Kit: 44258
Do Not Exceed Lower of Towing Vehicle
Manufacturer’s Rating or
500 (227 Kg) 5000 (2270 Kg)
Weight Carrying
Ball Mount
750 (341 Kg) 7500 (3405 Kg) Weight Distributing
Max Tongue
WT (LB)
Max Gross
Trailer WT (LB)
Hitch type
Wiring Access Location: SUV1, SUV2
2
5
6
7
3
4
Note: Fasteners typical
both sides
Warning: Do Not lubricate threads, bolt failure
may occur due to over tightening.
Warning: Do Not drill or weld to this hitch.
Important notes:
Use only Towing Products supplied or approved
Bolts, locknuts, and washers to install this hitch
SERIES 51®
Form: F205 Rev A 5-6-05