Reese 44703 PROFESSIONAL RECEIVER User Manual
Installation instructions, Part numbers
Installation Instructions
Chevrolet Silverado Pickup 1500
GMC Sierra Pickup 1500
(Requires OEM Bumper)
Part Numbers:
75866
87652
44703
Hitch Shown In Proper Position
Equipment Required:
Wrenches: 3/4, 22mm, 21mm 1-1/8”
open end wrench, & 1-1/8”
Drill Bits: None
Frame rail
Note : Factory installed
steel step bumper and
brackets must be used in
conjunction with this
hitch
Fasteners Typical Both Sides of Vehicle
Note: Factory Installed Steel Step Bumper and Brackets Must Be Used In Conjunction with Hitch
Note: Loosen the spare tire for ease of installment
1. Remove or trim out the cap in the step bumper.
2. Remove existing M14 bolts from end of each frame rail.
3. Lift hitch into position, locating rearmost holes in hitch under existing weldnuts in vehicle frame.
4. Install M14 bolts and conical washer, into weldnuts in vehicle frame at the step bumper attachment.
5. Install remaining fasteners as shown.
6. Tighten all fasteners to the required torque specification.
7. Re-tighten the spare tire
© 2013 Cequent Performance Products, Inc
Sheet 1 of 3
75866N
9-26-13
Rev. A
1
1
1
1
Qty. (2)
Hex bolt M14 X 2.0 X 40mm CL 10.9
6
6
6
6
Qty. (6)
Conical washer ½”
2
2
2
2
Qty. (2)
Lock washer 9/16”
7
7
7
7
Qty. (6)
Hex nut ½-13
3
3
3
3
Qty. (2)
Flat washer 9/16”
8
8
8
8
Qty. (1)
Hex bolt ¾-10 X 3.50 GR5
4
4
4
4
Qty. (6)
Carriage bolt ½-13 X 1-3/4” GR5
9
9
9
9
Qty. (1)
Conical washer ¾”
5
5
5
5
Qty. (6)
Spacer
Qty. (1)
Hex nut ¾-10
Tighten all ½-13 GR5 fasteners with torque wrench to75 Lb.-Ft. (102 N*M)
Tighten all M14 CL10.9 fasteners with torque wrench to 100 Lb.-Ft. (136 N*M)
Tighten all 3/4-10 GR 5 fasteners with torque wrench to 260 Lb.-Ft. (353 N*M)
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to prevent
entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working beneath a
vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and
SAE J684.
Fastener Kit: 75866F
Do Not Exceed Lower of Towing Vehicle
Manufacturer’s Rating or
Hitch type
Max Gross
Trailer WT (LB)
Max Tongue
WT (LB)
Weight Distributing
12,000 (5448 Kg)
1200 (545 Kg)
Weight Carrying
Ball Mount
6000 (2724 Kg)
900 (409 Kg)
Wiring Access Location: PU3
Form: F205 Rev C 9-17-2012
Accessory Rating
E
Printed in Mexico
Frame rail
4
6
5
3
7
8
9
1
2
Note: Fasteners typical both sides
Note : Factory installed
steel step bumper and
brackets must be used in
conjunction with this
hitch
Cross member and step
bumper shown in cut
view for clarity
Existing weldnut