Reese 44706 PROFESSIONAL RECEIVER - Manual

© 2014 Cequent Performance Products, Inc Sheet of 3 75882N 2-10-14 Rev. B
1. Lower spare tire.
2. Remove (8) torque head screws (4 on top, 4 on bottom) which attaches the bumper fascia to the bumper under structure.
3. Raise hitch into place as shown.
(Hint, raise one side of the forward attachment above leaf spring, then repeat on the other side)
4. Slide nut plate into the frame from the front of the vehicle as shown and hand tighten ½” bolts into place.
5. Remove rubber grommets and using the fish wire insert the two 7/16” bolts and two ½” bolts into their respective position.
6. Attach middle 7/16” bolts to hitch and hand tighten.
7. Slide 5/8” spacer blocks into place and pass ½” bolt through block and vehicle rearward slot as shown. Hand tighten.
8. Tighten all hitch fasteners to the torque specifications given.
9. Reinstall bumper fascia and raise spare tire into place
Installation Instructions
Ram Promaster
Except Extended Model
Part Numbers:
Hitch Shown In Proper Position
Wiring Access Location: SUV 3&4
Equipment Required: N/A
Fastener Kit: 75882F
Wrenches: 16mm, 3/4”, T-30
Qty. (2) ½”-13 nut plate Qty. (2) 7/16”-14 x 1.75 Carriage Bolt
Qty. (2) ½”-13 X 1.50 GR5 Hex Bolt Qty. (2) 1/4” X 3.00 X 1.00 Spacer Block
Qty. (4) ½” Conical Washer Qty. (2) 7/16” Conical Washer
Qty. (2) ½”-13 X 2.25 Gr. 5 Carriage Bolt Qty. (2) 7/16”-14 Hex Nut
Qty. (4) ¼” X 3.00 X 1.00 Spacer Block Qty. (2) ½” Fish Wire
Qty. (2) 5/8” X 2.0 X 1.5 Spacer Block Qty. (2) 7/16” Fish Wire
Qty. (2) ½”-13 Hex Nut
Note: Check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to prevent
entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working beneath a
vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and
SAE J684.
Do Not Exceed Lower of Towing Vehicle
Manufacturer’s Rating or
Form F206 Rev A 5605
75882
87655
44706
Note: Fasteners typical
both sides of hitch.
Tighten all 7/16”-14 Gr. 5 fasteners with torque wrench to 50 Lb.-Ft. (68 N*M)
Tighten all ½”-13 Gr. 5 fasteners with torque wrench to 75 Lb.-Ft. (102 N*M)
Figure 1
Accessory Rating D
Hitch Type
Max Gross
Trailer WT (LB)
Max Tongue
WT (LB)
Weight Distribution 7500 750
Weight Carrying
Ball Mount
6000 750
Bumper
Torque Head
Screws
Frame
1
2
3
4
5
6 13
1
8
9
10
11
12
7