Rivers Edge RE756 PADDED ARMREST_SHOOTING RAIL KIT - Manual

Padded Armrest & Shooting Rail Kit (RE756)
HuntRiversEdge.com
HuntRiversEdge.com
800-450-3343 • Fax (715) 822-2124
E-mail: [email protected]
TREESTANDS
Rivers Edge Treestands are engineered with you the hunter in mind.
We appreciate your purchase of one of our world class accessories.
Follow these few simple instructions and your stand will provide you
many years of trouble-free pleasure. Instructions should be kept in a
safe place and reviewed at least annually.
If for any reason you have a problem with your product,
DO NOT return
to the retailer, contact the Rivers Edge customer service department
at 800-450-EDGE (3343) for assistance.
ASSEMBLY INSTRUCTIONS
Tools needed – two 7/16" wrenches
IMPORTANT ASSEMBLY TIP: Do not tighten any nut and bolt combinations
completely until all parts are assembled together! Finger tighten plus one
turn of a wrench only! This will temporarily hold the lock nut on the bolt
while helping alignment of all parts! After all parts are assembled to-
gether, all nut & bolt combinations can be completely tightened.
NOTE: This kit fits Rivers Edge Action, Alpine, Jackpine, Tradesman &
Journeyman Ladders only!
1. Identify your ladder model by comparing it to
FIGURE 1, FIGURE 2 OR
FIGURE 3.
FOR ACTION LADDERS
2. a. Attach the armests to the top sitting section using (2) provided 1/4-20 x
2-1/4" bolts, locknuts and washers. SEE FIGURE 1. DO NOT tighten all
nut & bolt assemblies completely!
FOR ALL OThER LADDERS
2. a. Attach the blade end of seat/tree blade frame and the armrests to the side
rails using (2) provided 1/4-20 x 3” bolts, washers and locknuts. SEE FIGURE
2 OR 3.
3. Attach the front end of each armrest to the side rail using (2) provided 1/4-20
x 2-1/4" bolts and locknuts. SEE FIGURE 2 OR 3. You may now tighten all
nut & bolt assemblies. Be sure not to over tighten or crush tubing when
tightening!
4. a. Attach the shooting rail by simply setting the rail down over the studs
provided on the armrests. SEE FIGURES 1 & 2.
NOTE: Using powder graphite lubricant during assembly is highly
recommended at slide together points of each section to prevent
binding.
b. Attach the (2) provided 9” and (1) 18” camo foam pads to the armrests
and shooting rail by wrapping around tubing and attaching Velcro together.
OMRE75608
Rev. 1/31/08
© 2008 Rivers Edge Treestands, Inc.
All Rights Reserved.
wARNING
READ, UNDERSTAND AND FOLLOw ALL ASSEMBLY,
INSPECTION, MAINTENANCE & USE INSTRUCTIONS
PROVIDED BEFORE EACh USE. FAILURE TO FOLLOw
ALL wARNINGS AND INSTRUCTIONS COULD RESULT
IN SERIOUS INJURY OR DEATh.
BE SURE TO FOLLOw ALL INSTRUCTIONS PROVID-
ED wITh YOUR ORIGINAL LADDER STAND. IF ANY
INSTRUCTIONS ARE NOT UNDERSTOOD OR IF YOU
hAVE A PARTS ISSUE CALL 800-450-3343 BEFORE
USING.
DOUBLE ChECK ASSEMBLY STEPS TO BE CERTAIN
YOU hAVE CORRECTLY ASSEMBLED ThIS PROD-
UCT.
BE SURE ShOOTING RAIL IS SEATED ALL ThE wAY
DOwN ON STUDS DURING USE.
NEVER LEAN AGAINST, LEAN OVER, OR SIT ON
ShOOTING RAIL. IT IS DESIGNED AS A ShOOTING
RAIL ONLY. ALwAYS BE AwARE ThAT ThE ShOOTING
RAIL CAN SwING TO ONE SIDE OR ThE OThER.
BE SURE ShOOTING RAIL IS SET OFF TO ThE SIDE
(ON ONE STUD) whEN ASCENDING OR DESCENDING
LADDER.
DO NOT CRUSh TUBING whEN TIGhTENING BOLT
ASSEMBLIES! IDENTIFY AND FAMILIARIZE YOURSELF
wITh ALL PARTS BEFORE YOU START.
INSTRUCTIONS ShOULD BE KEPT IN A SAFE PLACE
AND REVIEwED AT LEAST ANNUALLY.