Rivers Edge RE713 10' PERIMETER - Manual (Page 2)

TREESTANDS
10' Perimeter ™ Ladder Pod (RE713)
Page 
HuntRiversEdge.com
HuntRiversEdge.com
800-450-EDGE (3343)
rivers edge Treestands are engineered with you the hunter in mind.
We appreciate your purchase of one of our world class ladder pods.
Follow these few simple instructions and your stand will provide you
many years of trouble-free pleasure. Instructions should be kept in a
safe place and reviewed at least annually.
If for any reason you have a problem with your product,
DO NOT
return to the retailer, contact the rivers edge customer service
department at 800-450-eDGe (3343) for assistance.
SELECTING A GOOD LOCATION
Assemble this product only in areas that meet the following criteria!
No overheard power lines near area; open, flat, level, dry ground of
sufficient size to allow for assembly, upright and climbing.
Approximate area needed for this is 14’ X 24’.
ASSEMBLY INSTRUCTIONS
Tools needed – two 7/16” wrenches, two 1/2” wrenches and a tape measure
to measure level ground area needed & cross brace length.
NOTE: It is highly recommended that as much assembly as possible be
done in a garage setting because of hardware amount and time involved!
Allow two-four hours for assembly.
IMPORTANT ASSEMBLY TIP: DO NOT TIGHTEN NUT & BOLT COMBI-
NATIONS UNTIL ALL PARTS ARE ASSEMBLED TOGETHER! FINGER
TIGHTEN ONLY PLUS ONE TURN OF A WRENCH ONLY! THIS WILL
TEMPORARILY HOLD THE LOCK NUT ON THE BOLT WHILE HELPING
ALIGNMENT OF ALL PARTS! WHEN ALL PARTS ARE ASSEMBLED
TOGETHER, ALL NUT & BOLT COMBINATIONS MUST BE COMPLETELY
TIGHTENED!
1. Attach (2) platforms (TP100) together using (2) provided 1/4-20 x 2-1/4”
bolts, locknuts and steel washers. SEE FIGURE 1. DO NOT tighten all
nut & bolt assemblies completely!
2. Attach the assembled platforms to the (2) provided J-receiver tubes
(TP109) using (4) provided 1/4-20 x 2-1/4” bolts, locknuts and steel
washers.
SEE FIGURE .
wARNING
READ, UNDERSTAND AND FOLLOw ALL ASSEMBLY,
INSPECTION, MAINTENANCE, & USE INSTRUCTIONS
PROVIDED BEFORE EACH USE. FAILURE TO FOLLOw
ALL wARNINGS AND INSTRUCTIONS COULD RESULT
IN SERIOUS INJURY OR DEATH.
DO NOT POSITION THIS PRODUCT ON A SLOPE, UNLEV-
EL OR wET GROUND. IT MAY TIP OVER AND YOU COULD
BE SERIOUSLY INJURED OR DEATH MAY OCCUR.
GROUND SHOULD BE SUCH THAT GOURND STAKES
(NOT INCLUDED) CAN BE DRIVEN INTO THE GROUND
THROUGH HOLES PROVIDED IN FOOT PADS. THIS wILL
HELP PREVENT POD FROM TIPPING OVER IN STRONG
wINDS. YOU wILL NEED TO MAKE (4) GROUND STAKES.
STAKES SHOULD BE 3/8” ROD X 4” LONG.
IT IS HIGHLY RECOMMENDED THAT YOU PURCHASE
AND USE THE UNIVERSAL TIE-DOwN KIT wITH GROUND
STAKES (RE758) wITH THIS PRODUCT TO HELP PRE-
VENT PERSONAL INJURY AND/OR PRODUCT DAMAGE
FROM TIPPING OVER IN STRONG wINDS.
ALL ASSEMBLY MUST BE DONE BY THREE PEOPLE IN
THIS ORDER AT GROUND LEVEL BEFORE UPRIGHT-
ING. DO NOT CRUSH TUBING wHEN TIGHTENING BOLT
ASSEMBLIES! IDENTIFY AND FAMILIARIZE YOURSELF
wITH ALL PARTS BEFORE YOU START. A BOLT IDENTI-
FICATION CHART CAN BE FOUND IN THE BACK.
FIGURE 1
1/4-20 x 2-1/4" bolts
locknuts
steel washers
1/4-20 x 2-1/4" bolts
J-receiver tubes locknuts
steel washers
FIGURE 
cut view of
platforms