Foredom C.TXR-1 - Manual (Page 2)

Parts List
C.SXR−1
Foot Control, 115V
FOREDOM
The Foredom Electric Company
16 Stony Hill Rd., Bethel, CT 06801 • 203−792−8622
Fax: 203−796−7861 • www.foredom.net
}
Qty Description Part No. Item
1 Cover CP10691 1
1 Trigger Switch CP11251 2
2 Screw, 6−32 X 5/16" CP10571 3
1 Circuit Board, SxR CP10874 4
1 Base CP10690 5
1 Pad CP10753 6
1 Specification Label SxR−1.LAB 7
1 Male Cordset CP10541 8
2 Hinge Pin CP10584C 9
1 Grommet CP10578 10
1 Lock Washer, #8 CP10564 11
1 Ring Terminal CP10580 12
1 Female Cordset CP10830 13
1 Screw, 8−32 x 1/4" CP10563 14
3 2 Wire Connector CP11029 15
1 Set Screw CP10562 16
1 Spring CP10588 17
1 Capacitor CP11248 18
1 Wire, White CP11036 19
Wiring Diagram
for SxR−1
Foot Control
Form DN 5/12
Circuit Board Female Receptacle
to Motor
Male Plug
AC Power
Source
Attach
Ground
Screw
to Base
3
4
2 1 5
6
Trigger Switch
Board
Capacitor
On older Switches, all the terminals will be push-in, spring clamp
type. For newer Switches, Terminal 1 has a screw for fastening
the wire lead. To remove wires from the push-in terminals, insert
1.3mm [.05in] approximate diameter pin or the blade of a jeweler's
screwdriver all the way into the terminal socket to release the
spring clamp. Grasp the tool and wire and pull them together out
of the socket. If you have difficulty removing the wires from the
push-in terminals and you have wire-cutting, stripping, and
soldering tools, you can cut the wires off where they exit from the
terminals. To prepare the cut wires for installation into the
replacement Switch, strip them back exactly 8.25 mm [5/16 in].
For the wires to be inserted into push-on terminals only, apply
solder to the stripped ends to fuse the strands together. DO NOT
solder wire ends to be inserted into screw terminals.
Install Cover over Spring (17) and align holes to Base.
Insert Pins (9) and seat them with hammer.
Connect Wires to New Trigger Switch and Circuit Board as
shown in the Wiring Diagram. Push wires all the way in, so
that no bare wire is exposed. For Screw Terminal 1, push wire
lead all the way into the socket then tighten the screw firmly. Push
the other wire lead all the way into terminal 6. Simultaneously
push the Capacitor leads all the way into terminals 3 and 5.
Pull on all the wire leads, making sure they are secure.
Install Board and Switch into Base using two Screws (3).
Position wires around post of Base so wires will not
interfere with Cover travel.
I.
Insert new Trigger Switch into Board.
E.
D.
C.
Remove two Screws (3) from Board (4). After the wires have
been removed from the switch, as instructed in paragraph C,
remove the switch from the board, insert the new switch in its
place, and follow the instructions in paragraphs E and F.
With a punch and hammer, drive two Pins (9) in until Cover (1) lifts
from Base (5). Remove Pins from Cover by driving them outward.
Disconnect Foot Control from Motor and Wall Outlet.
Instructions for Removing
and Replacing Trigger Switch
B.
A.
H.
G.
Locate the White Wire from the Male AC Power Cord then
follow it to the Wire Connector. Cut both white wires nearest
the connector then strip both wire ends 8.25mm [5/16in].
Insert three white wires into newly supplied connector and crimp.
F.
BLK
WHT
BLK
WHT
WH
T
WHT
WHT
BLK
BLK
GRN
GRN
4
3
5
7
8
10
13
9
11
12
14
15
17
1
16
2
Wire
Connectors
18
19
6
Jumper
Wire