LEDGlow Advanced 3 Million Wheel Well Kit - Manual

Advanced 3 Million USB Flexible Wheel Well Add-On Kit
Warning: Please check your state and local laws before installing this LED wheel well lighting kit. Every state has different policies and
procedures in place regarding aftermarket vehicle accessories. LEDGlow is not responsible for any fines that you may receive while using the
underbody kit. This kit is for off road use only.
Warning: The installation of this kit is recommended to be installed by a licensed professional. The improper installation of this kit will void all
warranties.
The Advanced 3 Million USB Extender Kit that connects the wheel well tubes to the USB control box must be installed in a dry location!
Having the extender kit exposed to water or the elements will cause it to fail. Any water damage or corrosion to this part will VOID all
warranties.
Kit Contents:
A. (4) 24” INCH EXTERIOR FLEXIBLE LED TUBES
B. (1) ADVANCED 3 MILLION USB EXTENDER KIT
Please read the following instructions thoroughly before installing this Advanced 3 Million USB Flexible Wheel Well Add-On Kit.
1. Arrange the tubes on the ground the way you plan to install them on the vehicle. Be sure to test the kit to ensure it
is functioning properly before installation.
2. Optional: Raise and support the vehicle if necessary, and remove the vehicle’s wheels.
3. Start with the driver’s side front tube. Mount the tube to your vehicle’s fender well above your tire using the
supplied screws. When mounting this tube make sure to keep it away from any moving parts or direct heat source.
Each wheel well tube is flexible and allows you to contour it directly to the fender well.
4. Complete the process explained in step 3 for the remaining wheel well tubes. Be sure to keep all wheel well tubes
and power wires away from any direct heat source or moving parts. NOTE: When installing the rear wheel well
tubes, make sure to keep each tube and their power wires at least 10 inches away from your exhaust.
5. If you removed your wheels in step 2, please reinstall them in accordance to factory specifications.
6. After you have installed all of the wheel well tubes, turn your steering wheel back and forth several times to
ensure there is enough clearance between your tire and each of the front tubes.
7. Find a secure and dry location to mount the USB extender kit. LEDGlow recommends mounting this inside the
vehicle close to your existing USB control box. The extender kit is not waterproof and cannot be mounted under
the hood. You will void the warranty if the extender kit is not mounted inside the cabin of the vehicle.
8. Connect the USB power wire that is included with the USB wheel well extender kit to any open port on the USB
extender kit that is powering your existing Advanced 3 Million Underbody Kit.
9. Starting with the rear tubes, run the power wires to the location of the USB extender kit. Make sure the power
wires are tightly secured when going around any suspension parts and the exhaust. Run and secure the power
wires along the upper section of the wheel well so there is no possibility of the wire falling onto the tire while the
vehicle is in motion. Make sure there is at least 10 inches between the exhaust or any direct heat source and the
power wires. Be sure not to pinch any of the power wires when running them, this kit may cause the kit to
malfunction and will void the warranty. Run the wires along the frame of the vehicle and make sure to tightly
secure them. Now run the front tube power wires to the extender kit location, again, keeping them away from any
moving parts or direct heat source.
10. It is extremely important to double check ALL of the power wires to ensure they are kept away from your wheel,
any moving parts, or direct heat source. Any excess or slack in the power wires will have to be bound up and
secured tightly.
11. DO NOT SHORTEN OR CUT ANY OF THE POWER WIRES. This will immediately void the warranty.
12. If your vehicle was raised you can now lower it. Power on the kit to ensure it is functioning properly.
13. With the vehicle on the ground, turn the steering wheel as far as it can go in both directions to ensure the tubes and
power wires do not come in contact with the tire. If a tube or wire is damaged by the tire due to improper
installation the warranty will be voided.