LEESON Mounting Instructions for FHP Series User Manual
J501, Main ac board, Pcm adder board
The FHP Series PCM Adder Board 175324.00 accepts a 0 - 5 VDC, 0 - 10 VDC, or 4-20
mA signal and outputs an isolated 0-5 VDC signal without requiring additional panel
space. It mounts directly over the main AC board (bottom board) thus maintaining the
same footprint. This instruction manual will give you step-by-step information for
successfully mounting the PCM Adder Board to your FHP Series drive.
The following diagram shows a FHP Series drive with the PCM adder board installed onto
the unit and the parts supplied in this kit.
MOUNTING INSTRUCTIONS
FOR FHP SERIES PCM ADDER BOARD
4
Leeson FHP Series PCM Adder Board 175324.00 Mounting Instructions
2100 Washington Street
Grafton, WI 53024-0241, U.S.A.
TEL: (262) 377-8810 FAX: (262) 377-9025
Document number 250-0367, Revision 0
Printed in the U.S.A. - January 2003
Copyright © 2003 by LEESON Electric - All rights reserved. No part of this document may be reproduced or transmitted in any form without
written permission from LEESON Electric. The information and technical data in this document are subject to change without notice.
LEESON Electric and its Divisions make no warranty of any kind with respect to this material, including, but not limited to, the implied
warranties of its merchantability and fitness for a given purpose. LEESON Electric and its Divisions assume no responsibility for any errors
that may appear in this document and make no commitment to update or to keep current the information in this manual.
6-PIN
HEADER (1)
6-32 x 1 5/16"
PHILLIPS SCREW (1)
0.578" NYLON
SPACER (1)
SHOULDER
WASHER (1)
PCB
STANDOFF (2)
JUMPER (1)
PCM ADDER
BOARD (1)
S1
S2
S3
E
1
D
J501
1:0-5VD
C
2:0-10VD
C
3
:4-
20M
JMP5
02
:INPUT TYP
E
TB5
01
2-3:
C
URREN
T
1-2:V
O
LTA
GE
PARTS SUPPLIED IN THIS KIT
Required Tools: Phillips Screwdriver
MAIN AC BOARD
(BOTTOM BOARD)
TB501
Y
U
W
J501
C501
C502
TH501
L
1
L
2
230
V
D
JMP5
02
:INPUT TYP
E
2-3:
C
URREN
T
1-2:V
O
LTA
GE
PCM ADDER
BOARD
SECURE THE
PCM ADDER
BOARD WITH
THE 6-32 x 1 5/16"
PHILLIPS SCREW.
S T E P # 8
V
U
W
J501
C501
C502
TH501
L
1
L
2
1
1
5
V
230
V
DECEL
D
JMP501:INPUT R
A
1:0-5V
D
2:0-10
V
3
:4
-20M
J
MP
502
:INP
U
T TYP
E
TB5
01
2-3:
C
URREN
T
1-2:V
O
LTA
GE
POSITION THE PCM
ADDER BOARD OVER
THE BOTTOM BOARD
AS SHOWN.
NOTE: First align the
bottom holes of J501 (on
the PCM adder board) with
the 6 pin header installed
on the bottom board. The
PCM adder board will
snap into place at J501
and the two standoffs.
S T E P # 7
TB501
V
U
W
J501
C501
C502
TH501
L
1
L
2
1
1
5
V
230
V
TQ
DECEL
S2
S3
D
0
1:INP
U
T RAN
GE
1:0-5VD
C
2:0
1
0VDC
JMP5
02
:INPUT TYP
E
TB5
01
2-3:
C
URREN
T
1-2:V
O
LTA
GE
J501
INSTALLATION COMPLETE.
IC502
J501
JMP501