Luxor|H.Wilson LE54WT - Manual

Instruction Sheet - L
E Model Tables
Models L
E-26 and LE-27 Two Shelf Mobile Tables
Models L
E-34, LE-40, LE-42, LE-48 and LE-54 Three Shelf Mobile Tables Models L
E26 & LE27
1 - Bottom shelf with casters sockets
1 - Top shelf with handle
4 - Long legs
4 - Casters (2 w/brake)
1 - Plug housing cover
2 - Sheet metal screws
Optional Electric Assembly:
1 - Electric cord
1 - Power cord retaining bracket
1 - Cord tie
3 - Sheet metal screws
Models L
E34, LE40, LE42,
L
E48 & LE54
1 - Bottom shelf with casters sockets
1 - Top shelf with handle
1 - Center shelf with eight leg posts
4 - Short legs
4 - Long legs
4 - Casters (2 w/brake)
1 - Plug housing cover
2 - Sheet metal screws
Tools Required:
1 - Rubber Mallet
1 - Slotted Screwdriver
PARTS LIST
L
E - Two Shelf Model
L
E - Three Shelf Model
1
Lay top shelf (with handle) ribbed side up on a
smooth surface. Push all 4 legs onto leg posts.
IMPORTANT:
If your L
E table does not have the Optional
Electrical Assembly start by closing the elec-
tric plug housing in the handle of the top shelf
as illustrated. If your L
E table has the Optional
Electric Assembly, see assembly instructions
below. Start by assembling electric.
1
Firmly seat electrical assembly 3 plug unit into
handle plug housing as illustrated. Secure with
power cord plug retaining bracket. Thread cord
through cord retaining track and out the open-
ing in the side of the handle.
2
Secure power cord management tie into starter
hole with sheet metal screws. See illustration
A. Secure with power cord management tie by
wrapping tie around cord and fastening. Cut off
any unnecessary extra length of tie.
3
Wrap the cord
around the
handle.
4
For safety and neat
appearance secure cord
plug to cord by utilizing
plug snap.
2
Position bottom shelf, ribbed side up, over the 4
legs and insert leg posts into legs. Using a
rubber mallet, firmly hammer bottom shelf into
legs until all 4 legs are seated (flush) against the
surfaces of both shelves.
4
Position bottom shelf, ribbed side up, over the 4
legs and insert leg posts into legs. Using a
rubber mallet, firmly hammer bottom shelf into
legs until all 4 legs are seated (flush) against the
surfaces of both shelves.
2
Position center shelf (with 8 leg posts) ribbed
side up, over the 4 legs and insert leg posts into
legs. Using a rubber mallet, firmly hammer cen-
ter shelf into legs until all 4 legs are seated
(flush) against the surfaces of both shelves.
3
Push remaining 4 legs into leg posts of center
shelf.
3
Push the four casters firmly into the holes in
each corner of the bottom shelf. Important:
Casters must be fully seated. Tap firmly with
rubber mallet to properly seat casters. Turn your
LP table right side up. It is now ready for use.
5
Push the four casters firmly into the holes in
each corner of the bottom shelf. Important:
Casters must be fully seated. Tap firmly with
rubber mallet to properly seat casters. Turn
your L
E table right side up. It is now ready for
use.
1
Models L
E-34 and LP-40: Lay top shelf (with
handle) ribbed side up on a smooth surface.
Push all 4 short legs onto leg posts.
Models L
E-42, LE-48 and LE-54: Lay top
shelf (with handle) ribbed side up on a smooth
surface. Push all 4 long legs onto leg posts.
Models L
E-34, LE-40, LE-42, LE-
48 and L
E-54
Models LP-26 and LP-27
LONG LEGS
LEG POST
CORD
RETAINING
TRACK #2
CORD
RETAINING
TRACK #1
A
CORD MANAGEMENT TIE
POWER CORD
MANAGEMENT TIES
TIE IS IN SECURED
POSITION
3 PLUG UNIT POWER CORD PLUG
RETAINING BRACKET
FRONT
BACK
LEG POST
*Models L
E34 and LE40 use short legs first.
*Models L
E42, LE48 and LE54 use long legs first.
*Models L E34 and LE40
use long legs second.
*Models L
E42, LE48 and
L
E54 use short legs second.
PLACE LOCKING CASTERS
AS ILLUSTRATED
FOR BIG WHEEL
ASSEMBLY.
See instructions
in Big Wheel
hardware pack.
FRONT
BACK
PLACE LOCKING CASTERS
AS ILLUSTRATED
FOR BIG WHEEL
ASSEMBLY.
See instructions
in Big Wheel
hardware pack.
PLUG
HOUSING
COVER
Customer Service Dept
2245 Delany Rd
Waukegan, IL 60087
Ph: 847/244-1800 • 800/323-4656
Fax: 847/244-1818 • 800/327-1698