Luxor|H.Wilson LEM32TT - Manual

Instruction Sheet
Endura Models LEM32, LEM32T & LEM32TT
LEM32 LEM32T LEM32TT
PARTS LIST
LEM32 LEM32T LEM32TT
IMPORTANT
The electrical unit should
be assembled first.
2.
Lay terminal platform (long narrow shelf with grommet hole)
ribbed side up on a smooth surface. Push 1 set of short legs
onto leg posts. Set aside temporarily and continue with step
No. 3.
3.
Lay middle shelf
(with handle) ribbed
side up on a smooth
surface. Push all 4
long legs onto leg
posts.
4.
Position bottom shelf with open cut-out facing toward the front, ribbed
side up, over the 4 legs of the top shelf as illustrated. Insert leg posts
into legs. Using a rubber mallet, firmly hammer bottom shelf into legs
until all four legs are seated (flush) against the surfaces of both
shelves.
5.
Push the four casters firmly into the holes in each corner of
the bottom shelf. Important: casters must be fully seated. Tap
firmly with rubber mallet to properly seat casters. Turn your
Endura Workstation right side up.
6.
Set terminal platform as completed in Step No. 2 right side up and
set its legs onto leg posts of middle shelf. Grommet hole should be
to the back of terminal platform. Firmly hammer terminal platform
with legs onto leg posts of middle shelf until legs are seated (flush)
against the surface of middle shelf and terminal platform. Your
Endura Computer Workstation is now ready for use.
CORD GUIDE COVER
TERMINAL
PLATFORM
GROMMET CAP
CORD GUIDE COVER
MIDDLE SHELF
GROMMET CAP
GROMMET RING
CABLE GROMMET HOLE
GROMMET RING
LEG POST
FRONT
BACK
LEG
POST
LEG
POST
LOCKING CASTERS
1.
Install grommet
rings by tapping into
place with rubber
mallet. Snap off cord
guide cover from
grommet cap so
equipment plug may
be run through
grommet to plug
unit, then insert
grommet cap into
grommet ring.
Tools Required:
Rubber Mallet
www.luxorfurn.com
www.hwilson.com
x1 - 24x32 Top Shelf w/
Handle
x4 - 17.5˝ Legs
x1 - 24x32 Bottom Shelf w/
Cutout
x1 - Set of 4˝ Casters
2 w/ Locking Brake
x1 - Electric Assembly
x2 - Cable Clips
x1 - Grommet Cord Guide
x1 - 24x12 Terminal Platform
x4 - 8˝ Legs
x1 - 24x32 Middle Shelf w/
Handle
x4 - 17.5˝ Legs
x1 - 24x32 Bottom Shelf w/
Cutout
x1 - Set of 4˝ Casters
2 w/ Locking Brake
x1 - Electric Assembly
x2 - Cable Clips
x2 - Grommet Cord Guide
x1 - 24x12 Terminal Platform
x1 - 24x32 Middle Shelf w/
Handle
x8 - 20˝ Legs
x1 - 24x32 Bottom Shelf w/
Cutout
x1 - Set of 4˝ Casters
2 w/ Locking Brake
x1 - Electric Assembly
x2 - Cable Clips
x2 - Grommet Cord Guide
1
Firmly seat electrical assembly 3 plug unit into
handle plug housing as illustrated. Secure with
power cord plug retaining bracket. Thread cord
through cord retaining track and out the open-
ing in the side of the handle.
2
Secure power cord management tie into starter
hole with sheet metal screws. See illustration
A. Secure with power cord management tie by
wrapping tie around cord and fastening. Cut off
any unnecessary extra length of tie.
3
Wrap the cord
around the handle.
4
For safety and neat
appearance secure cord
plug to cord by utilizing
plug snap.
CORD
RETAINING
TRACK #2
CORD
RETAINING
TRACK #1
3 PLUG UNIT
POWER CORD PLUG
RETAINING BRACKET
A
CORD MANAGEMENT TIE
POWER CORD
MANAGEMENT TIES
TIE IS IN SECURED
POSITION
LEM32T / LEM32TT
For LEM32T &
LEM32TT
Upated 10/5/12