Steelcraft Automotive 422800p 4 PREMIUM OVAL SIDE BAR - Manual

SIDEBAR (BENT END)
2010 DODGE RAM 25-3500 MEGA CAB
Page 1 of 4 1/21/10 (DP)
PARTS LIST:
Qty Description Qty Description
1 Driver/Left Sidebar 4 12-1.75mm x 40mm Bolt/10-1.5mm Nut Plates
1 Passenger/Right Sidebar 4 12-1.75mm x 40mm Bolt Plates
1 Driver/Left Front Mounting Bracket 8 12mm x 32mm OD x 3mm Flat Washers
1 Passenger/Right Front Mounting Bracket 8 12mm Lock Washers
1 Driver/Left Front Support Bracket 8 12mm Hex Nuts
1 Passenger/Right Front Support Bracket 8 12mm Plastic Retainers
1 Driver/Left Center Mounting Bracket 8 10-1.50mm x 35mm Hex Bolts
1 Passenger/Right Center Mounting Bracket 4 10mm x 30mm OD x 2.5mm Flat Washers
2 Rear Mounting Brackets 8 10mm x 20mm OD x 2.5mm Flat Washers
1 Driver/Left Rear Support Mounting Bracket 8 10mm Lock Washers
1 Passenger/Right Support Mounting Bracket 4 10mm Hex Nuts
2 Rear Support Strap 2 8-1.25mm x 25mm Hex Bolt
4 1/2” x 2” Hex Bolts 2 8mm x 24mm OD x 2mm Flat Washers
4 1/2” Lock Washers 2 8mm Lock Washers
4 1/2 ” X 1-1/2” OD x 1/8" Flat Washers
PROCEDURE:
1. REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ
INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION.
2. Starting at the driver side-front of the vehicle, remove the tape covering the factory oval holes
in the inner body panel located by the front tire. Partially thread a Plastic Retainer onto the
threaded end of a Bolt and Nut Plate, (Fig 1A). Once you have assembled the Bolt and Nut
Plate, insert it into the factory oval hole. Hold the Bolt end with one hand and tighten the
Plastic Retainer with your other hand. NOTE: Tighten the Plastic Retainer until it is flush
against the side panel, (Figure 2). IMPORTANT: The Plastic Retainer is designed to prevent
the Bolt Plate from falling into the body cavity and to aid in mounting the Bracket.
3. Next, select (1) 12mm Bolt Plate and partially thread a Plastic Retainer onto it. Insert the Bolt
Plate into the forward, smaller oval hole and install as per Step 2, (Fig 1B & 2).
4. Select the driver side front Mounting Bracket. Position the Mounting Bracket onto the installed
Bolt Plates. Secure it with (2) 12mm Flat Washers, (2) 12mm Lock Washers and (2) 12mm
Passenger
Side Rear
Mounting
Bracket
Passenger Side
Front Mounting
Bracket
Driver Side
Rear
Mounting
Bracket
Driver Side
Front Mounting
Bracket
12mm x 40mm Bolt/10mm Nut
Plate (pictured with Plastic
Retainer and 10mm Hex Bolt)
12mm x 40mm Bolt Plate
(pictured with Plastic Retainer
installed for example)
Passenger Side Front
Support Bracket
Driver Side Front
Support Bracket
Driver Side
Center
Mounting
Bracket
Passenger Side Rear
Support Mounting Bracket
Driver Side Rear Support
Mounting Bracket
Passenger Side Center Mounting
Bracket
Rear
Support
Strap Rear
Support
Strap