Sunex Tools SX545B - Manual (Page 4)

SX545B 4 Rev. 05/19/03
Nipple
Operating Instructions • Warning Information • Parts Breakdown
Air Supply...
Tools of this class operate on a wide range of air pressures. It is
recommended that air pressure of these tools measure 90 PSI at
the tool while running free. Higher pressure (over 90 psig; 6.2
bar) raises performance beyond the rated capacity of the tool,
which will shorten tool life because of faster wear and could cause
injury. Always use clean, dry air. Dust, corrosive fumes and/or
water in the air line will cause damage to the tool. Drain the air
tank daily. Clean the air inlet filter screen on at least a weekly
schedule. The recommended hookup procedure can be viewed in
the above figure.
The air inlet used for connecting air supply, has standard 1/4"
NPT. Line pressure should be increased to compensate for unusually
long air hoses (over 25 feet). Minimum hose diameter should be
3/8" I.D. and fittings should have the same inside dimensions and
be tightly secured.
Lubrication...
Lubricate the air motor daily with quality air tool oil. If no air line
oiler is used, run a teaspoon of oil through the tool. The oil can
be squirted into the tool air inlet or into the hose at the nearest
connection to the air supply, then run the tool. The amount of oil to
be used is 1 ounce. Overfilling will cause a reduction in the power
of the tool.
Operation...
Locate center of new hole by using a center punch. Place drill bit
tip in punch mark. Hold drill square with work and start motor.
Apply steady, even pressure. Do not force. Too much pressure can
cause bit to break or overheat. Too little pressure will keep bit from
cutting and cause it to overheat. Reduce pressure just before bit
cuts through the work. When bit has penetrated work and is
spinning freely, take it from the work while the motor is running,
then turn off drill. If the drill jams in the work, release throttle
immediately.
Disconnect the drill before removing bit and determining cause of
trouble. Do not attempt to free the bit by starting and stopping
the motor.
Forward &
Reverse Lever
Air Inlet
Limited Warranty...
SUNEX INTERNATIONAL, INC. WARRANTS TO ITS CUSTOMERS
THAT THE COMPANY’S SUNEX TOOLS
® BRANDED PRODUCTS
ARE FREE FROM DEFECTS IN WORKMANSHIP AND MATERIALS.
Sunex International, Inc. will repair or replace its Sunex Tools ®
branded products which fail to give satisfactory service due to
defective workmanship or materials, based upon the terms and
conditions of the following described warranty plans attributed to
that specific product. This product carries a ONE-YEAR warranty.
During this warranty period, Sunex Tools will repair or replace at
our option any part or unit which proves to be defective in material
or workmanship.
This warranty does not cover damage to equipment or tools arising
from alteration, abuse, misuse, damage and does not cover any
repairs or replacement made by anyone other than Sunex Tools or
its authorized warranty service centers.The foregoing obligation is
Sunex Tools’ sole liability under this or any implied warranty and
under no circumstances shall we be liable for any incidental or
consequential damages.
Note: Some states do not allow the exclusion or limitation of
incidental or consequential damages, so the above limitation or
exclusion may not apply to you. Return equipment or parts to
Sunex Tools, or an authorized warranty service center,
transportation prepaid. Be certain to include your name and
address, evidence of the purchase date, and description of the
suspected defect.
If you have any questions about warranty service, please write to
Sunex Tools. This warranty gives you specific legal rights and you
may also have other rights which vary from state to state. Repair
kits and replacement parts are available for many of Sunex Tools
products, regardless of whether or not the product is still covered by
a warranty plan.
Shipping Address: Sunex Tools, 315 Hawkins Rd.,
Travelers Rest, SC 29690
Mailing Address: Sunex Tools, P.O. Box 4215,
Greenville, SC 29608
SX-545Bman_051903 5/19/03 4:44 PM Page 4