System Sensor 2W-MOD2 - Manual (Page 4)

D500-46-00 4 I56-2174-004
©2006 System Sensor
System Sensor warrants its enclosed product to be free from defects in
materials and workmanship under normal use and service for a period
of three years from date of manufacture. System Sensor makes no other
express warranty for the enclosed product. No agent, representative,
dealer, or employee of the Company has the authority to increase or alter
the obligations or limitations of this Warranty. The Company’s obliga-
tion of this Warranty shall be limited to the replacement of any part of
the product which is found to be defective in materials or workman-
ship under normal use and service during the three year period com-
mencing with the date of manufacture. After phoning System Sensor’s
toll free number 800-SENSOR2 (736-7672) for a Return Authorization
number, send defective units postage prepaid to: System Sensor, Returns
Specifications:
Electrical
Mechanical
Supply Voltage - Min. 8.5 Volts (Power limited) Height: 4.5 inches
Max. 30 Volts (Power limited) Width: 4.0 inches
Max.Ripple Voltage: 30% of applied voltage Depth: 1.25 inches
Max. Standby Current: 30mA (12 detectors on loop) Weight: 0.5 pound
Max. Alarm Current: 90mA (Includes packaging
Alarm Contact Ratings: 0.5 Amp @ 36 V DC, Resistive materials)
Maintenance Contact Ratings: 2 Amp @ 30 V DC, Resistive
Min. Reset Voltage: 6 Volts
Min. Reset Time: 0.3 sec.
Operating Temperature Range: 14°F to 122°F (-10°C to 50 °C)
Operating Humidity Range: 0 to 95% RH non-condensing
Storage Temperature Range: –4°F to 158°F (–20°C to 70 °C)
Initial Communication Cycle: 2-6 minutes after power-up or panel reset
EZ Walk Test Available: 6 minutes after power-up or panel reset
2-wire compatibility
Min. loop voltage: 10 Volts
Max. loop voltage: 11.5 Volts
Max. loop resistance: 50 ohm
Max. loop ripple: 1 Vpp
Max. Loading Capacitance: 0.01 mF
Max. Alarm current: 40 mA
Max. Reset Voltage: 0.3 V
Alarm Delay: No
Min. Alarm reset time: 0.3 sec.
Max. normal load current: 1.25 mA
Zone Type: Standard
EOL Device: 3.9 KΩ (0.25W, 5%)
Loop style: B, D
Compatibility/Zone identifier: A
Max. detectors per zone: Models 2W–B and 2WT–B: 12
Model 2WTR–B: 1
Model 2WTA–B: 1
NOTE: When used with the RRS–MOD reversal relay/synchroniza-
tion module and the 2W–MOD2, a maximum of 12 2WTA–B detec-
tors are allowed per zone.
FCC Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to pro-
vide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
Three-Year Limited Warranty
Department, RA #__________, 3825 Ohio Avenue, St. Charles, IL 60174.
Please include a note describing the malfunction and suspected cause
of failure. The Company shall not be obligated to replace units which
are found to be defective because of damage, unreasonable use, modi-
fications, or alterations occurring after the date of manufacture. In no
case shall the Company be liable for any consequential or incidental
damages for breach of this or any other Warranty, expressed or implied
whatsoever, even if the loss or damage is caused by the Company’s
negligence or fault. Some states do not allow the exclusion or limita-
tion of incidental or consequential damages, so the above limitation or
exclusion may not apply to you. This Warranty gives you specific legal
rights, and you may also have other rights which vary from state to state.