System Sensor MOD2W - Manual (Page 4)

TESTING
Modules must be tested after installation and following periodic maintenance.
Testing should be performed at least once per year.
NOTE: Before testing, notify the proper authorities that the system will be
temporarily out of service. Disable the zone or system to prevent any un-
wanted alarms.
EZ WALK TEST
The communication loop between the module and detectors can be manually
tested by putting the module and detectors into EZ Walk test mode.
The EZ Walk loop test verifies the initiating loop wiring and provides visual
status indication at each detector:
1. Ensure proper wiring and power is applied. Wait approximately 5 min-
utes from power-up before performing the EZ Walk test. The green LED
on the module must be blinking indicating the module is in ready/
standby mode to start the EZ Walk mode.
2. Locate the EZ Walk recessed test switch located behind the module cover
(See Figure 1). Depress the test switch with a small screwdriver. The
yellow LED will blink showing that the module and detectors are in EZ
Walk mode for 5 minutes.
3. Observe the LEDs at each detector to make sure the green LED is double
blinking every 5 seconds as listed in Table 3.
4. At the end of the five minute period, the module will terminate EZ Walk
and the yellow LED will stop blinking. The EZ Walk test period can be
extended by pressing the test switch multiple times. Each press will add
5 minutes of additional time.
If a module or detector fails the test, its wiring should be checked. If the
module still fails, it should be replaced. Notify the proper authorities when all
testing has been completed.
NOTE: The EZ Walk loop test should not be used in lieu of functional testing
(alarm, trouble and other functional tests) of the system.
TABLE 3: EZ WALK TEST DETECTOR MODES
DETECTOR
GREEN LED
DETECTOR
RED LED
PROPER OPERATION Double Blink 5 Seconds OFF
OUT OF SENSITIVIY OFF Double Blink 5 Seconds
FREEZE CONDITION OFF Double Blink 10 Seconds
SS-560-000 4 I56-4001-000
©2013 System Sensor
System Sensor warrants its enclosed product to be free from defects in materials and
workmanship under normal use and service for a period of three years from date of
manufacture. System Sensor makes no other express warranty for the enclosed product.
No agent, representative, dealer, or employee of the Company has the authority to in-
crease or alter the obligations or limitations of this Warranty. The Company’s obligation
of this Warranty shall be limited to the replacement of any part of the product which
is found to be defective in materials or workmanship under normal use and service
during the three year period commencing with the date of manufacture. After phoning
System Sensor’s toll free number 800-SENSOR2 (736-7672) for a Return Authorization
number, send defective units postage prepaid to: System Sensor, Returns Department, RA #__________, 3825 Ohio Avenue, St. Charles, IL 60174. Please include a note describing
the malfunction and suspected cause of failure. The Company shall not be obligated to
replace units which are found to be defective because of damage, unreasonable use,
modifications, or alterations occurring after the date of manufacture. In no case shall the
Company be liable for any consequential or incidental damages for breach of this or any
other Warranty, expressed or implied whatsoever, even if the loss or damage is caused by
the Company’s negligence or fault. Some states do not allow the exclusion or limitation of
incidental or consequential damages, so the above limitation or exclusion may not apply
to you. This Warranty gives you specific legal rights, and you may also have other rights
which vary from state to state.
THREE-YEAR LIMITED WARRANTY
FCC STATEMENT
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used
in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installa-
tion. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.