AllerAir A8PK7025 - Manual (Page 4)

REFILING THE CARBON CANISTER HEPA & CARBON FILTERS ORDER GUIDE
These replacement filters will extend the life of your AllerAir unit. Please be sure
to follow the instructions for changing the filters in your unit.
We recommend changing pre-filters every two months, HEPA filters every
three to five years, and carbon filters every two years.
Your AllerAir unit contains two filters. The carbon filter is the smaller, innermost one.
Philips screwdriver, garbage bag large enough to hold all of the old carbon, rubber mallet.
* Please note that this is a messy, dust-producing job, so select attire and site for the task accordingly.
AllerAir makes a special funnel to evenly refill carbon filters.
Call 1-888-852-8247 during regular business hours (EST) or e-mail to order.
Tools required:
Please use the numbers in the chart when placing your order.
Call AllerAir at 1-888-852-8247 during regular business hours (EST)
or send an e-mail to [email protected]
Order Reference Numbers
Order Reference Numbers
Models 8000
D Models
DX Models
DS Models
A8FMR002
Models 8000
Exec Models 2.5"** A8FCB325
Vocarb Models 2.5"** A8FCB225
D Exec Models 3" A8FCB330
D Vocarb Models 3" A8FCB230
DX Exec Models 3.5" A8FCB335
DX Vocarb Models 3.5" A8FCB235
DS Models 3"
Models 8000 Notes
2.5" Canister** A8FC1501 Exec and Vocarb models
D Models A8FC0503
DX Models A8FC1503
*Please refer to your carbon filter depth when ordering a replacement
*Please use the above part numbers when ordering your replacement parts.
*Please consult the Bulk Carbon Order Guide
Models 4000 Notes
Exec Mix AM000911
Vocarb Mix AM000912
Tobacco Smoke MixAM000901
Special Blend Mix
*Please use the above part numbers when ordering your replacement parts
please call
Models 8000
Exec, Vocarb A8FH0411
NOTE: Please use the above part numbers when ordering your replacement parts
STEP 1
Remove the carbon filter from
the unit by pressing thumbs
against the inner rim and pulling up. STEP 2
Gently pull back the pre-filter to
access the four screws at the top
of the filter. Remove the screws with
a Philips screwdriver and take off
the lid of the filter. STEP 3
Discard all of the old carbon.
Pour it into a garbage bag of
adequate size and tie the
bag shut.
STEP 4
Pour in the new carbon, using a
funnel if desired. As you pour, tap
the sides of the filter with the rubber
mallet to help settle the carbon
granules. STEP 5
When the filter is full, replace the lid
and its screws. Adjust the pre-filter,
and gently slide the filter back into
the unit. STEP 6
Replace the felt gasket.
Replace the base of the unit.
Align the arrow on the base's
gold sticker with the unit's seam,
and replace the four screws with
a Philips screwdriver.
Microparticulate Electrostatic Filter Order Guide
Replacement Carbon Filter Order Guide*
HEPA Filter Order Guide
NOTE: Please use the above part numbers when ordering your replacement parts
This is the filter that wraps around any D, DX, DS or MCS carbon filter.
*Please use the above part numbers when ordering your replacement parts.
If you have ordered a special blend of carbon in the past please let us know about it when ordering the
replacement
**Please refer to your carbon filter depth when ordering a replacement
Empty Carbon Canisters Order Guide*
Bulk Carbon Order Guide*
AllerAir Industries Inc. Toll free: 1-888-852-8247 / Fax: 1-877-688-2193 www.allerair.com
5 4
AllerAir Industries Inc. Toll free: 1-888-852-8247 / Fax: 1-877-688-2193 www.allerair.com