Teka TKS2 650 - Manual (Page 13)

13 EN
Auxiliary function
Cancel audio warning
Your dryer will give an audio warning when the
programme comes to an end. If you do not
want to hear the audio warning, press “Cancel
Audio Warning” button. The relevant light
will turn on when this button is pressed and
an audio warning will not be given when the
programme comes to an end.
C
You can select this function either before or
after the programme starts.
Warning indicators
C
Warning indicators may differ according to
the model of your dryer.
Filter cleaning
A warning light will turn on to remind filter
cleaning after the programme finishes.
C
If the filter cleaning warning light lights up
continuously, please refer to, “Suggested
solutions for problems”.
Starting the programme
1. Press “Start/Pause/Cancel” button to start
the programme.
2. Light of the “Start/Pause/Cancel” button
will turn on to indicate that the programme
has started.
Progress of program
Progress of a running program is shown
through the program follow-up indicator.
At the beginning of every program step, the
relevant indicator LED will light up and light of
the completed step will turn off.
“Drying”:
Drying level will be illuminated during the whole
drying process until the drying degree reaches
“iron dry”.
“Iron Dry”:
Starts to illuminate when the drying degree
reaches “iron dry” step and remains illuminated
until the next step.
“Ready to wear”:
Starts to illuminate when the drying degree
reaches “Ready to wear” step and remains
illuminated until the next step.
“Final / Anti-creasing”:
Illuminates when the program comes to an end
and anti-creasing function is activated.
C
If more than one LED light up or
flash concurrently, it means there is
malfunctioning or a failure (please see,
Solution suggestions for problems).
Changing the programme after it has
started
You can use this feature to dry your clothes
under higher or lower temperatures after your
dryer has started.
For example;
1. Press and hold the “Start/Pause/Cancel”
button for about 3 seconds to “Cancel”
the programme in order to select “Extra
Dry” programme instead of “Iron Dry”
programme.
2. Select the “Extra Dry” programme by
rotating the programme selection button.
3. Press “Start/Pause/Cancel” button to start
the programme.
C
Press “Start/Pause/Cancel” button for 3
seconds to cancel the programme or turn
the programme selection knob in any
direction to end the programme while the
machine is running. Water tank and filter
cleaning warning lights turn on to warn the
user when the programme is cancelled by
pressing the “Start/Pause/Cancel” button
for 3 seconds. However, the warning
lights do not turn on when the programme
is cancelled by turning the programme
selection knob. Only the drying light turns
on and the machine remains in hold until
a new programme is selected and the
“Start/Pause/Cancel” button is pressed.
Child-proof lock of the machine should not
be active in order to perform these two
operations. If the child-proof lock is active,
deactivate it before performing these
operations.
Adding/removing laundry in standby mode
In order to add or remove laundry after the
programme starts:
1. Press the “Start/Pause/Cancel” button to
switch the dryer to “Pause” mode. Drying
process will stop.
2. Open the door at “Pause” position and
close it again after adding or taking out
laundry.
3. Press “Start/Pause/Cancel” button to start
the programme.
C
Any laundry added after the drying process
has started may cause the dried clothes in
the machine intermingle with wet clothes
and the result will be wet laundry after the
drying process is over.
C
Laundry may be added or taken out
as much as desired during a drying
process, but this process will extend the
programme duration and increase energy
consumption since the drying will be
interrupted continuously. Therefore, it is
recommended to add laundry before the
drying programme has started.
Child-proof lock
There is a child-proof lock to prevent any
programme interruption due to the pressing of
button while the programme is running. The
loading door and all buttons except the “On/
Off” button on the control panel are deactivated
when the child-proof lock is active.
Press the “Start/Pause/Cancel” and “Cancel