Teledyne LeCroy Summit T3-16 PCI Express Protocol Analyzer QSG - Manual (Page 4)

Trademarks and Servicemarks
Teledyne LeCroy and Summit T3-16 are trademarks of Teledyne
LeCroy. Microsoft and Windows are registered trademarks of
Microsoft Inc.
All other trademarks are property of their respective companies.
Changes
Product specifications are subject to change without notice.
Teledyne LeCroy reserves the right to revise the information in this
document without notice or penalty.
Teledyne LeCroy Customer Support
Online Download
Periodically check the Teledyne LeCroy Protocol Solutions Group
web site for software updates and other support related to this
product. Software updates are available to users with a current
Maintenance Agreement.
Mail: 3385 Scott Blvd., Santa Clara, CA 95054-3115
Web: teledynelecroy.com/Support/SoftwareDownload/
E-mail: [email protected]
Tel: (800) 909-7112 (USA and Canada)
Tel: (408) 653-1260 (worldwide)
Fax: (408) 727-6622 (worldwide)
© 2012 Teledyne LeCroy, Inc. All rights reserved. Part Number: 923221-00 Rev A
This document may be printed and reproduced without additional permission, but all copies should contain this copyright notice.
Making Your First Recording
Connect Summit T3 to the system under test using an interposer or probe, and then configure the Recording Options.
You can then test the Analyzer by creating a short snapshot recording.
Connect Summit T3 to System under Test using an Interposer or Probe
For a slot interposer, do the following:
1. Insert the slot interposer into a PCI Express slot that you want to monitor.
2. Insert the PCI Express device into the PCIe connector on top of the interposer.
3. Connect Summit T3 to the interposer with Analyzer Y cables. Connect cable Side A to the Upstream port of the
Analyzer, and connect cable Side B to the Downstream port. Note: If you are using x16 interposer, the lower connector
carries lanes 0 to 7, and the upper connector carries lanes 8 to 15.
4. Connect power to the interposer using the provided 12-V power adapter.
For Mid Bus Probe or other types of probes and interposers, please see the Summit T3-16 User Manual.
Configure Recording Options
1. From the Setup menu, select Recording Options.
2. Select the General tab and then choose Summit T3 as the Analyzer type.
3. In the Link section, specify the lane width of the PCI Express link to be analyzed. The rest of the settings in this section
can be left at the factory defaults for most PCI Express systems.
4. For multi-lane PCI Express links, the Analyzer needs to observe link training to record link traffic correctly.
5. Click OK at the bottom of the Recording Options dialog box to apply the Analyzer recording settings specified.
Start Recording
1. Start a recording session by clicking the Record button in the toolbar. Recording is tracked and reported on an
activity meter in the status bar.
2. After the recording buffer fills, uploading starts automatically. PCI Express traffic is saved to the hard drive as the file
specified in the recording options, and this file is opened in the application for you to view the traffic.
Note: You can interrupt a session by pressing the Stop button. If Recording is finished and Upload has started but has not
finished, a message box appears. You can:
• Continue uploading.
• Abort the upload and flush the data.
• Abort the upload and preserve all the previously saved data.
Using a USB Connection
To set up the Analyzer using a USB connection:
1.
Install PETracer software on the host machine.
2. Connect the Analyzer to a 100-volt to 240-volt, 50 Hz to
60 Hz, 120 W power outlet using the provided power cord.
3. Connect the USB port to a USB port on the host machine
using a USB cable.
4. Turn on the power switch on the front of the analyzer.
Note: At power-on, the Analyzer initializes and performs a
self-diagnostic. The results are reflected by messages on the
Summit T3-16 LCD display. If the LCD display indicates
failure, call Teledyne LeCroy Customer Support for
assistance.
5. Summit T3 will be recognized by the host machine as a USB
device.
Follow the Microsoft
® Windows ® on-screen Plug-and-Play
instructions for the automatic installation of the Analyzer as a
USB device on your analyzing host machine. (The required
USB drivers are included on the Installation CD and were
installed on your system when you installed the software.)
Click Finish when you see the message that says “Windows
has finished installing the software that your new hardware
requires” and the file has been installed in your host machine.
8. Start the PETracer software, so you can start working with
Summit T3.
9