Vestil ASP Series - Manual (Page 3)

10/27/2010 rev. 10/27/2010 APS manual.doc
Failure to read and understand the instructions included in this manual before
using or servicing the step stand constitutes misuse of the product.
Study the entire manual before you use the product for the first time and before each subsequent use. Read the
manual to refresh your understanding of the safe use, inspection and maintenance procedures explained on p. 3-5. If
questions remain about the product after you finish reading the manual, ask your employer or supervisor for help. DO
NOT attempt to resolve any problems with the step stand unless you are authorized to do so and are certain that it will be
safe to use afterwards.
S AFETY G UIDELINES
Electrocution might result if the step stand contacts electrified wires. Reduce the likelihood of electrocution
by applying common sense:
 DO NOT contact electrified wires with any part of the step stand;
 DO NOT use the steps in an area where contact with electrified wires is likely;
 DO NOT use the steps close to electrified wires or other sources of electricity;
 Before using the steps, always inspect the usage area for unusual conditions that require special precautions.
Read the entire manual before installing option kits or adjusting or using the step stand. If
questions remain after you finish reading the manual, ask your supervisor or employer for clarification. Improper assembly
or installation might result in serious personal injuries:
 ALWAYS level the step stand before using it. (See “Leveling the step stand” on p. 5).
 DO NOT store items, materials, etc. on the step stand.
 DO NOT place weight that exceeds the maximum rated load (capacity) on one or more steps.
 DO NOT use a structurally compromised step stand. Examples of structural damage include: broken or severely
damaged posts (legs), steps, or frame, and damage caused by rust or corrosion. Inspect the step stand according to
the inspection instructions on p. 4. DO NOT use the steps unless the unit and all installed options pass every part of
the inspection.
ASP-PORT Option Package:
I NSTALLATION AND U SE I NSTRUCTIONS
ASP-PORT is NOT a handrail! Do not lean against or apply weight
to the handle except as necessary to transport to step stand (see Step 5 below).
Step 1: Hold the PORT handle assembly up to the side of your ASP-series step stand;
then mark the stand with the locations of the 3 bolt holes. [NOTE: The right side of the
handle should roughly align with the rear legs. See diagram below.]
Step 2: Drill each of the holes using the 9/32in. drill bit included in the hardware kit.
Step 3: Fasten the handle to the step stand. Feed a bolt through each of the holes,
and secure it with a flat washer and ¼ in. hex nut.
Step 4: Adjust the height of the legs so that the step stand rests firmly on all 4 (rubber)
feet.
Step 5: To transport the step stand, grasp the top of the handle, brace the wheel shaft
with your foot, and tilt the stand toward you until the wheels contact the ground.
FIG. 1B: Hardware kit
7
Bolt tab
(circled)
FIG. 1A:
ASP-PORT
(includes
hardware kit: 3
bolts, 3 flat
washers, 3 hex
nuts, and drill
bit
Bolt holes
Frame
supporting
uppermost
step
Rear
legs
Right side
Wheel
shaft
6
3
2
1
FIG. 1C: ASP-
PORT fastened to
step stand
Item
No. Part
Number
Description Quantity
1 14-525-001 Handle weldment 1
2
16-132-009
Hard rubber wheel
1¼in. x 4in. 2
3
65078
1/8in. x 1½in. zinc-
plated cotter pin 2
4 ND87060 9/32 in. drill bit 1
5 11009
¼ in. – 20 x 1½ in.
zinc-plated HHCS #2
bolt 3
6 33004
¼ in. type A narrow
flat washer
3
7 37018
¼ in. – 20 zinc-plated
UNC nylock nut
3
5
4
p. 3 of 5
Copyright 2010 Vestil Manufacturing Corp.