Extron Electronics XTRA Full Rack Series User Guide - Manual (Page 24)

Audio output
Number/signal type
XPA 2002 ................................ 2 channels, 4 or 8 ohms; or 1 bridged mono, 8 ohms
XPA 2002-70V ......................... 2 channels, 70 V
XPA 2002-100V ....................... 2 channels, 100 V
XPA 2003C-70V ....................... 2 channels, 4 or 8 ohms
1 channel, 70 V
XPA 2003C-100V ..................... 2 channels, 4 or 8 ohms
1 channel, 100 V
XPA 2004 ................................ 4 channels, 4 or 8 ohms; or 2 bridged mono, 8 ohms
Connectors
XPA 2002 ................................ (1) 5 mm screw lock captive screw connector, 4 pole
XPA 2002-70V, XPA 2002-100V (2) 5 mm screw lock captive screw connectors, 2 pole
XPA 2003C-70V, XPA 2003C-100V
(1) 5 mm screw lock captive screw connector, 4 pole
(1) 5 mm screw lock captive screw connector, 2 pole
XPA 2004 ................................ (2) 5 mm screw lock captive screw connectors, 4 pole
NOTE: These connectors accept wires of 22 AWG to 12 AWG.
Load impedance
XPA 2002-70V ......................... 25 ohms minimum
XPA 2002-100V ....................... 50 ohms minimum
XPA 2003C-70V
Channel 1 or 2 ................... 4 ohms minimum
Channel 3 .......................... 25 ohms minimum
XPA 2003C-100V
Channel 1 or 2 ................... 4 ohms minimum
Channel 3 .......................... 50 ohms minimum
XPA 2002, XPA 2004 ............... 4 ohms (8 ohms if bridged) minimum
Amplifier type ................................ Class D
Output power
XPA 2002-70V ......................... 200 watts rms per channel, 70 V, 1 kHz, 0.1% THD
XPA 2002-100V ....................... 200 watts rms per channel, 100 V, 1 kHz, 0.1% THD
XPA 2003C-70V
Channel 1 or 2 (8 ohm) ...... 100 watts rms per channel, 8 ohms, 1 kHz, 0.1% THD
Channel 1 or 2 (4 ohm) ...... 200 watts rms per channel, 4 ohms, 1 kHz, 0.1% THD
Channel 3 (70 V output) .... 200 watts rms per channel, 70 V, 1 kHz, 0.1% THD
XPA 2003C-100V
Channel 1 or 2 (8 ohm) ...... 100 watts rms per channel, 8 ohms, 1 kHz, 0.1% THD
Channel 1 or 2 (4 ohm) ...... 200 watts rms per channel, 4 ohms, 1 kHz, 0.1% THD
Channel 3 (100 V output) .. 200 watts rms per channel, 100 V, 1 kHz, 0.1% THD
XPA 2002, XPA 2004 ............... 100 watts rms per channel, 8 ohms, 1 kHz, 0.05% THD
200 watts rms per channel, 4 ohms, 1 kHz, 0.05% THD
400 watts rms (bridged mono), 8 ohms, 1 kHz, 0.05% THD
Frequency response ........................ 20 Hz to 20 kHz, ±1 dB
THD + Noise
XPA 2002-70V, XPA 2002-100V 0.1%, 1 kHz, 3 dB below clipping
XPA 2003C-70V, XPA 2003C-100V
Channels 1 and 2: 0.1%, 20 Hz-20 kHz, 8 ohms, 3 dB below
clipping
Channel 3: 0.1%, 1 kHz, 3 dB below clipping
XPA 2002, XPA 2004 ............... 0.1%, 20 Hz to 20 kHz, 8 ohms, 3 dB below clipping
XTRA Full Rack Power Amplifier Series • Reference Information 19