Wiegmann ULTIMATE - Manual (Page 4)

J4
www.hubbell-wiegmann.com
Data Subject To Change Without Notice
G E N E R A L E N C L O S U R E A C C E S S O R I E S
D R I P S H I E L D S • H O L E S E A L S
F E AT U R E S - S P E C I F I C AT I O N S
D R I P S H I E L D S
• Designed to protect door hardware from dripping
water and settling dust
• Drip shields attach easily to the enclosure with stainless
steel screws, gasket and sealing washers (hardware
is furnished)
• Drip shields fit all single door NEMA 12 and NEMA 4
wall mounted enclosures
• Stainless steel door clamps are furnished to replace the
standard door clamps
• Steel drip shields have a ANSI 61 gray polyester pow-
der finish over phosphatized surfaces
• Stainless steel drip shields have a grained finish
• 42", 48", 60" and 72" drip shields fit floor mounted
double door enclosures. Specify when ordering for
double door wall mounted enclosures
CATALOG NUMBER
GAUGE
FITS ENCLOSURE
STEEL STAINLESS STEEL WIDTH
D K 1 2 S S D K 1 2 1 4 1 2 . 0 0 ( 3 0 5 )
D K 1 6 S S D K 1 6 1 4 1 6 . 0 0 ( 4 0 6 )
D K 2 0 S S D K 2 0 1 4 2 0 . 0 0 ( 5 0 8 )
D K 2 4 S S D K 2 4 1 4 2 4 . 0 0 ( 6 1 0 )
D K 3 0 S S D K 3 0 1 4 3 0 . 0 0 ( 7 6 2 )
D K 3 6 S S D K 3 6 1 4 3 6 . 0 0 ( 9 1 4 )
D K 4 2 — 1 4 4 2 . 0 0 ( 1 0 6 7 )
D K 4 8 — 1 4 4 8 . 0 0 ( 1 2 1 9 )
D K 6 0 — 1 4 6 0 . 0 0 ( 1 5 2 4 )
D K 7 2 — 1 4 7 2 . 0 0 ( 1 8 2 9 )
D R I P S H I E L D S
Drip Shields
H O L E S E A L S
Designed to seal extra push-button holes, conduit
openings, and knockout openings from dirt, dust,
oil and water
Steel:
• Quick wing nut
• Oil resistant gasket
• ANSI 61 gray polyester powder
Stainless Steel:
• Quick wing nut
• Oil resistant gasket
• Grained finish
CATALOG NUMBER
DESCRIPTION
HOLE
STEEL STAINLESS STEEL DIAMETER
WA S P B G WA S P B G S S
M i n i a t u r e o i l t i g h t
p u s h b u t t o n h o l e s
0 . 8 8 ( 2 2 )
WA S 0 5 0 WA S 0 5 0 S S 1 / 2 - i n c h c o n d u i t h o l e s 0 . 8 8 ( 2 2 )
WA S 0 7 5 WA S 0 7 5 S S 3 / 4 - i n c h c o n d u i t h o l e s 1 . 1 3 ( 2 9 )
WA S P B WA S P B S S
S t a n d a r d o i l - t i g h t
p u s h b u t t o n h o l e s
1 . 2 0 ( 3 0 )
WA S 1 0 0 WA S 1 0 0 S S 1 - i n c h c o n d u i t h o l e s 1 . 3 8 ( 3 5 )
WA S 1 2 5 WA S 1 2 5 S S 1 1 / 4 - i n c h c o n d u i t h o l e s 1 . 6 3 ( 4 1 )
WA S 1 5 0 WA S 1 5 0 S S 1 1 / 2 - i n c h c o n d u i t h o l e s 2 . 0 0 ( 5 1 )
WA S 2 0 0 WA S 2 0 0 S S 2 - i n c h c o n d u i t h o l e s 2 . 5 0 ( 6 4 )
WA S 2 5 0 — 2 1 / 2 - i n c h c o n d u i t h o l e s 3 . 0 0 ( 7 6 )
WA S 3 0 0 — 3 - i n c h c o n d u i t h o l e s 3 . 6 3 ( 9 2 )
WA S 3 5 0 — 3 1 / 2 - i n c h c o n d u i t h o l e s 4 . 0 0 ( 1 0 2 )
WA S 4 0 0 — 4 - i n c h c o n d u i t h o l e s 4 . 6 3 ( 1 1 8 )
H O L E S E A L S
Hole Seals