Watlow Series 97 - Manual (Page 27)

[InP1]
Input 1 Menu
[`SEt]
Setup Page
[`SEt] Setup Page
[SEn1] Sensor Type 1
[In`1] Input 1
[rL`1] Range Low 1
[rh`1] Range High 1
[dEC1] Decimal 1
[Ftr1] Input Software Filter 1
[`SEt] Setup Page
[In`2] Input 2
[E`Fn] Event Function
[E`cn] Event Condition
[`SEt] Setup Page
[LSid] Set Limit Active Sides
[LhYS] Limit Hysteresis
[`SEt] Setup Page
[Ot`2] Output 2
[hys2] Alarm Hysteresis 2
[LAt2] Latching 2
[SiL2] Silencing 2
[Sid2] Alarm Active Sides 2
[Lgc2] Alarm Logic 2
[Anu2] Alarm Annunciation 2
[`SEt] Setup Page
[Ot`3] Output 3
[hys3] Alarm Hysteresis 3
[LAt3] Latching 3
[SiL3] Silencing 3
[Sid3] Alarm Active Sides 3
[Lgc3] Alarm Logic 3
[Anu3] Alarm Annunciation 3
[`SEt] Setup Page
[Ot`4] Output 4
[hys4] Alarm Hysteresis 4
[LAt4] Latching 4
[SiL4] Silencing 4
[Sid4] Alarm Active Sides 4
[Lgc4] Alarm Logic 4
[Anu4] Alarm Annunciation 4
[Aout] Analog Output 4
[Prc4] Process 4 Type
[A`hi] Analog Output High
[A`Lo] Analog Output Low
[ACAL] Analog Output Offset
[BaUd] Baud Rate
[Addr] Address
[Udsp] Upper Display
[UP`L] Upper Display
User Limit Message
[Ldsp] Lower Display
[Lo`S] Lower Display
User Safe Message
[Lo`L] Lower Display
User Limit Message
[`SEt] Setup Page
[`C-F] C or F
[`Err] Input Error Latching
‰
‰
‰
‰
‰
‰
¿
¿
¿
¿
¿
¿
[InP2]
Input 2 Menu
[`SEt]
[Out1]
Output 1 Menu
[`SEt]
[Out2]
Output 2 Menu
[`SEt]
[Out3]
Output 3 Menu
[`SEt]
[Out4]
Output 4 Menu
[`SEt]
‰
‰
[Disp]
Display Menu
[`SEt]
[GLbL]
Global Menu
[`SEt]
¯
¯
¯
¯
¯
¿
¯
¯
Wa t l o w S e r i e s 9 7 N a v i g a t i o n ■ 4 . 5
Factory Page
‰
‰
[Fcty] Factory Page
[OPEr] Operations Page Mode
[`SEt] Setup Page Lock
[`CAL] Calibration Menu Lock
[Fcty] Factory Page
[MdL] Model Number
[dAtE] Date of Manufacture
[`Sn1] Serial Number 1
[`Sn2] Serial Number 2
[Soft] Software ID Number
[`rEu] Software Revision
[Ity2] Input 2 Hardware Enabled
[Oty1] Output 1 Hardware
[Oty2] Output 2 Hardware
[Oty3] Output 3 Hardware
[Oty4] Output 4 Hardware
[tout] Test Output
[dISP] Test Displays
[hrES] High Resolution
[AMb] Ambient Temperature
[Acnt] Ambient A-D Counts
[cnt1] Channel 1 A-D Counts
[cnt2] Channel 2 A-D Counts
[tSht] Communication Test /
Troubleshooting
[Line] Line Frequency
¿
[`LOC]
Lockout Menu
[FctY]
[dIAg]
Diagnostics Menu
[FctY]
¯
Note: The Factory Page also includes calibration
parameters that are not necessary for everyday use of
the controller. Calibration parameters and procedures
are explained in the Appendix.