STI 7533 - Manual

backbox mounting tab slots. Use rubber
mallet if necessa
in closed position, against the wall. Mark and
drill (4) 1/4 in. diameter holes. Insert the (4)
19033 anchors.
3
inst
through the access hole at
view
wires are not pinched between the wall and cabinet.
Drive in the (4) screws. Cabinet is now secure.
I
of cabinet. Select at least two
optional mounting holes. Mark and drill 3/16 in.
diameter holes and inst
mounting plate and the siren backplate. Nex
drive the (2) alarm mounting screws into the
previous inst
the terminal sw
screws and provided tool.
19033 ANCHOR
(4) PROVIDED
EME
RGE NCY USE
ON L Y
STI-7532 - KEY LOCK
STI-7533 & STI-7533AED - THUMB LOCK
STO
P
07530WR
ADJUSTABLE WIRE SHELF
INCLUDED WITH STI-7533AED
0
MOUNTING
TAB SLOTS
04875 MOUNTING PLATE
19002 SCREW
#8-32 x 3/8 in.
(4) PROVIDED
OPTIONAL SHELF
MOUNTING POSITION
06298
MOUNTING TABS
(4) PROVIDED
19013 SCREW
#10 x 1 1/2 in.
(4) PROVIDED
07530 CABINET
ASSEMBLY
6297530
GASKET
INSTALLATION OF STI-7532, STI-7533 & STI-7533AED PROTECTIVE CABINET
A
9 VOLT ALKALINE BATTERY
06201 STOP ALARM COVER
19016 TAMPERPROOF TOOL
(1) PROVIDED
19032 KEY (2) PROVIDED
19011 SCREW - TAMPERPROOF
(2) PROVIDED
19039 SCREW
#6 x 1 1/4 in.
(2) PROVIDED
19018 ANCHOR
(2) PROVIDED
MAGNETIC CONTACT
REED SWITCH
ALARM MOUNTING PLATE
06202 BACKPLATE
STO
P
EME
RGE
NCY
US
E O
NLY
Safety Technology International, Inc. • 2306 Airport Rd. • Waterford, Michigan 48327-1209 • 800-888-4784 • Fax: 248-673-1246 • Web: www.sti-usa.com • Email: [email protected]
INSTALLATION OF CABINET
1. Insert the (4) 06298 mounting tabs fully into
back box mounting tab slots. Use rubber mallet
if necessary.
2. After selecting a suitable location, place
cabinet in closed position, against the wall.
Mark and drill (4) 1/4 in. diameter holes.
Insert the (4) 19033 anchors.
3. Select one of the two shelf mounting locations,
install shelf. Close and lock cabinet.
4. Place cabinet in position making sure the (2)
switch wires are not pinched between the wall
and cabinet. Drive in the (4) screws. Cabinet is
now secure.
1. Place the alarm mounting plate on the top
center of cabinet. Select at least two of the
four optional mounting holes. Mark and drill
3/16 in. holes and install the 19018 anchors.
2. Fish the magnetic switch wires through the
alarm mounting plate and the siren backplate
(View A). Next, drive the two alarm mounting
screws into the previous installed anchors.
3. Install the two magnetic switch wires following
the terminal switch diagram (View B).
4. Install the alarm cover using the (2)
tamperproof screws and provided tool.
INSTALLATION OF ALARM ASSEMBLY
EMERGENCY USE ONLY
FRONT
5.375 in.
(137mm)
R.H. SIDE
backbox mounting tab slots. Use rubber
mallet if necessa
in closed position, against the wall. Mark and
drill (4) 1/4 in. diameter holes. Insert the (4)
19033 anchors.
3
inst
through the access hole at
view Close and lock cabinet.
4
wires are not pinched between the wall and cabinet.
Drive in the (4) screws. Cabinet is now secure.
I
of cabinet. Select at least two
optional mounting holes. Mark and drill 3/16 in.
diameter holes and inst
mounting plate and the siren backplate. Nex
drive the (2) alarm mounting screws into the
previous inst
the terminal sw
screws and provided tool.
1
STOP
23 in.
(584mm)
12.2 in.
(310mm)
14.2 in.
(360mm)
2.25 in.
(57mm)
6.44 in.
(164mm)
S
1/4” DIA.
v
moun
orien
as sho
t
(4) 1/4 in. diame
and c
(Do no
ALARM MOUNTING PLATE
CABINET
WIRE ACCESS HOLE
ROUTE THE 2 SWITCH WIRES
THROUGH THE HOLE AS SHOWN
OPTIONAL MOUNTING
HOLES (4)
v
moun
orien
as sho
t
(4) 1/4 in. diame
and c
W
(Do no
VIEW A