STI 46100 - Manual

INSTRUCTION GUIDE
Wireless Motion-Activated Chime STI-46100
(STI-46010 transmitter only)
STI-46100 compatible with STI-32000, STI-32600,
STI-32500, STI-32530, STI-33010, STI-35500, STI-46010
STI-46010 compatible with STI-32000, STI-32600,
STI-32500, STI-46100, STI-32530
ENCLOSED YOU WILL FIND
• Door Chime Receiver*
• Motion Sensor Transmitter
• Mounting Bracket
• Wall anchors
• Screws
*The Receiver is for indoor use only (included with
STI-46100 only).
TOOLS NEEDED:
• Small Phillips screwdriver
BATTERIES NEEDED (not included):
• Four AA alkaline batteries
MOTION SENSOR INSTALLATION
Note: The motion sensor can be mounted or set
anywhere, indoors or outdoors, at a height up to 10 feet
from the ground. For best range and detection, mount at
least 6 feet from the ground.
FOR MOUNTING
A. Place adjustable mounting bracket (provided) where
desired (such as a post, wall, house) and install top
screw into key slot. Then secure the bottom screw.
B. Slide the motion sensor down onto the bracket. Adjust
the motion sensor to the desired angle.
Note: To tighten the ball joint, use a Phillips screwdriver to
turn the adjustment screw on the bracket.
Important: The bottom cover must face downward after
installation so moisture cannot enter.
SET-UP
1. Remove bottom cover by simultaneously pressing
down on tabs and pulling cover out.
2. Set switch to chime mode.
3. Install four AA alkaline batteries into the battery
compartment. Be sure the battery (+) and (-) terminals
match (+) and (-) contacts shown on compartment.
4. Replace bottom cover.
TEST
1. Plug Receiver into any "live" standard AC outlet not
controlled by a switch.
2. Walk through the coverage area. Note when the chime
sounds. If the coverage area needs to be changed,
adjust the motion sensor for improved coverage.
Retighten the ball joint screw.
TO CHANGE TONE/MELODY OR ALARM
1. Remove bottom cover by simultaneously pressing down
on tabs and pulling cover out.
2. Set switch to "CHIME" position to play tone/melody, or
set to "ALARM" position to play warning sound. When
set to "ALARM" position, two seconds after motion
detection, the Receiver will generate its warning sound
and keep on making it for 45 seconds or until the switch
is set to "CHIME" position.
3. To change tone to different tone or melody, press once
on the "SCROLL" button. Receiver will play next
selection. To continue changing melody or selection,
press down once again and wait for Receiver to
confirm change.
Note: If you change songs or tones too rapidly, the
Receiver will not play each selection. Only last melody or
tone selected will play. Selecting while Receiver is
playing will switch system to new setting, but Receiver
will only finish playing tone or melody already in progress.
DETECTION ZONE
Motion is detected in a 40 x 140° range which will be over
1954 sq. feet. The mounting bracket can be adjusted to
customize the detection zone.
Note: As with most motion detection devices, pets or
other animals may activate the unit. Also, walking in a
straight line towards the motion sensor may reduce
operating range. Walking across the detection field
provides the maximum operational range.
VOLUME CONTROL
Adjust loudness by moving volume control lever on back
of Chime Receiver to desired position.
CHANGING THE SYSTEM CODE (optional)
The user can change the system code signal if
interference occurs with operation. If you use other
wireless products in your home, there is a slight
possibility of interference. Use the following instructions
to change the current system code setting to a new
setting.
Important: If you change the system code on the motion
sensor, you must also change the code on the Chime
Receiver. If the system code does not match on both
items, the system will not function properly.
It is NOT necessary to change the privacy code unless
interference occurs. If you need to change code:
1. Unplug chime Receiver from 120 volt AC outlet.
2. Remove screw from Receiver
wire compartment located on
back of chime and remove wire
cover.
3. Use a nail clipper to cut and
separate one or more of the wires
(“A” through “E”) on Chime
Receiver. Make sure cut wire
does not touch any other wire.
4. Remove the wireless motion
sensor bottom cover.
5. Using a nail clipper, cut and
separate the same wire that was
cut on the Chime Receiver. Make
sure the cut wire does not touch
any other wire.
6. Replace wire cover.
TROUBLESHOOTING TIPS
PROBLEM: Receiver does not sound when there is motion
in front of the motion sensor.
SUGGESTION: Replace batteries in the motion sensor
transmitter. Check that the Receiver is within 100’ of the
motion sensor. Check that the system code is the same in
the motion sensor and in the Receiver. Check that metal
objects do not block the motion sensor signal or move the
Receiver.
PROBLEM: Receiver sounds randomly.
SUGGESTION: Change the system code in the motion
sensor and the Receiver.
SPECIFICATIONS
Motion Sensor - Auto Chime shut off - 45 seconds
Transmission Range: 100’
Detection Field: 40’ x 140°
Batteries: 4 AA alkaline batteries
CHIME RECEIVER
Voltage: 120VAC, 60Hz
LIMITED WARRANTY
The product you have purchased is guaranteed against
defects in workmanship and materials for the period
stated on the package. Warranties implied by law are
subject to the same time period limitation. Some states do
not allow limitations on how long an implied warranty
lasts, so this time limitation may not apply to you. If the
product fails due to a manufacturing defect during normal
use, return the product and dated sales receipt to the
store where purchased for replacement.
Not Covered - Batteries, light bulbs and other expendable
items are not covered by this warranty. Repair service,
adjustment and calibration due to misuse, abuse or
negligence are not covered by this warranty.
Unauthorized service or modification of the product or of
any furnished components will void this warranty in its
entirety. This warranty does not include reimbursement
for inconvenience, installation, set-up time, loss of use,
postage, unauthorized service or other products used in
conjunction with, but are not supplied by, STI. All requests
for replacement must include a dated sales receipt. STI IS
NOT LIABLE FOR LOST PROFITS, INDIRECT, SPECIAL,
EXEMPLARY,
INCIDENTAL OR CONSEQUENTIAL
DAMAGES INCLUDING WITHOUT LIMITATION ANY SUCH
DAMAGES DUE TO IMPROPER WIRING OR MISUSE OF
THE PRODUCT. As some states do not allow the exclusion
or limitation of incidental or consequential damages, the
above limitation and exclusion may not apply to you.
This device complies with Part 15 of the FCC rules.
Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received,
including interference that may cause undesired
operation.
This device complies with RSS-210 of Industry Canada.
ALSO AVAILABLE FROM STI
• Wireless Doorbell Extender – lets you hear your existing
wired doorbell in remote areas of your home or yard
• Plug-in and Battery Doorbells and Chimes
• Wireless Driveway Monitor
• Solar Powered Lighted House Number
This warranty gives you specific legal rights, and you
may also have other rights which vary from state to state.
If you have questions or need further assistance, please
call Customer Service at: 1-800-888-4784 Mon. - Fri., 9
a.m.- 5 p.m. EST.
Electronic warranty form at www.sti-usa.com/wc14.
Patents #5,365,214, #5,680,102 & #5,680,112
Made in China
TRANSMITTER PRIVACY
CODE WIRES
Safety Technology International, Inc.
2306 Airport Road • Waterford, Michigan 48327-1209
www.sti-usa.com
©2007 STI 0407 STI-46100
WIRELESS CHIME
RECEIVER PRIVACY
CODE WIRES
SCROLL BUTTON