STI 34409 - Manual (Page 2)

Tilt Sensor: (Fig. 4)
• Alert Signal – Sensor is tilted more than 45° from vertical.
• Restore Signal – Sensor is tilted less than 45° from vertical.
When using the Tilt Sensor, the arrow on the bottom should point straight up in the non-triggered state.
— 2 —
Operation
Magnetic Sensor: (Fig. 3)
• Alert Signal – Magnet is over approximately 1 1/3 inches from the device.
• Restore Signal – Magnet is brought within approximately 1 inch from the device.
When using the Magnetic Sensor, the bottom case may be inserted into the top case in reverse
depending on which direction the Magnetic Sensor should face.
APPROXIMATE GAP (1 INCH)
GAP MAY BE EFFECTED
IF MOUNTED ON METAL.
“RESTORE”
CLOSED
“ALERT”
CLOSED
“ALERT”
OPENED
APPROXIMATE GAP (1 INCH)
GAP MAY BE EFFECTED
IF MOUNTED ON METAL.
REED SWITCH CABLE
(18 INCHES)
APPROXIMATE GAP
(GREATER THAN 1 1/3 INCHES)
GAP MAY BE EFFECTED
IF MOUNTED ON METAL.
“ALERT”
“RESTORE”
“ALERT”
OPENED
APPROXIMATE GAP
(GREATER THAN 1 1/3 INCHES)
GAP MAY BE EFFECTED
IF MOUNTED ON METAL.
VINYL ELECTRICAL
TAPE
19039 SCREW
(2) PROVIDED
KNOCK OUT FOR WIRES
OF EXTERNAL SWITCH
J2
J1 J3
“RESTORE”
CLOSED
“ALERT”
OPEN
MAGNETIC SENSOR
“ALERT”
“RESTORE”
TILT SENSOR EXTERNAL TERMINALS
“RESTORE”
CLOSED
“ALERT”
OPEN
EXTERNAL SWITCH
CONNECTION BLOCK
ONBOARD REED SWITCH
LOCATION FOR
MAGNETIC SENSOR
EXTERNAL SWITCH
CONNECTION BLOCK
TAMPER SWITCH
ONBOARD
REED SWITCH
OPTION 1 MOUNTING
(DOUBLE SIDED FOAM TAPE)
OPTION 2 MOUNTING
VINYL ELECTRICAL
TAPE
19039 SCREW
(2) PROVIDED
KNOCK OUT FOR WIRES
OF EXTERNAL SWITCH
EXTERNAL SWITCH
CONNECTION BLOCK
TAMPER SWITCH
ONBOARD
REED SWITCH
APPROXIMATE GAP (1 INCH)
GAP MAY BE EFFECTED
IF MOUNTED ON METAL.
“RESTORE”
CLOSED
“ALERT”
CLOSED
“ALERT”
OPENED
APPROXIMATE GAP (1 INCH)
GAP MAY BE EFFECTED
IF MOUNTED ON METAL.
REED SWITCH CABLE
(18 INCHES)
APPROXIMATE GAP
(GREATER THAN 1 1/3 INCHES)
GAP MAY BE EFFECTED
IF MOUNTED ON METAL.
“ALERT”
“RESTORE”
“ALERT”
OPENED
APPROXIMATE GAP
(GREATER THAN 1 1/3 INCHES)
GAP MAY BE EFFECTED
IF MOUNTED ON METAL.
VINYL ELECTRICAL
TAPE
19039 SCREW
(2) PROVIDED
KNOCK OUT FOR WIRES
OF EXTERNAL SWITCH
J2
J1 J3
“RESTORE”
CLOSED
“ALERT”
OPEN
MAGNETIC SENSOR
“ALERT”
“RESTORE”
TILT SENSOR EXTERNAL TERMINALS
“RESTORE”
CLOSED
“ALERT”
OPEN
EXTERNAL SWITCH
CONNECTION BLOCK
ONBOARD REED SWITCH
LOCATION FOR
MAGNETIC SENSOR
EXTERNAL SWITCH
CONNECTION BLOCK
TAMPER SWITCH
ONBOARD
REED SWITCH
OPTION 1 MOUNTING
(DOUBLE SIDED FOAM TAPE)
OPTION 2 MOUNTING
VINYL ELECTRICAL
TAPE
19039 SCREW
(2) PROVIDED
KNOCK OUT FOR WIRES
OF EXTERNAL SWITCH
EXTERNAL SWITCH
CONNECTION BLOCK
TAMPER SWITCH
ONBOARD
REED SWITCH
APPROXIMATE GAP (1 INCH)
GAP MAY BE EFFECTED
IF MOUNTED ON METAL.
“RESTORE”
CLOSED
“ALERT”
CLOSED
“ALERT”
OPENED
APPROXIMATE GAP (1 INCH)
GAP MAY BE EFFECTED
IF MOUNTED ON METAL.
REED SWITCH CABLE
(18 INCHES)
APPROXIMATE GAP
(GREATER THAN 1 1/3 INCHES)
GAP MAY BE EFFECTED
IF MOUNTED ON METAL.
“ALERT”
“RESTORE”
“ALERT”
OPENED
APPROXIMATE GAP
(GREATER THAN 1 1/3 INCHES)
GAP MAY BE EFFECTED
IF MOUNTED ON METAL.
VINYL ELECTRICAL
TAPE
19039 SCREW
(2) PROVIDED
KNOCK OUT FOR WIRES
OF EXTERNAL SWITCH
J2
J1 J3
“RESTORE”
CLOSED
“ALERT”
OPEN
MAGNETIC SENSOR
“ALERT”
“RESTORE”
TILT SENSOR EXTERNAL TERMINALS
“RESTORE”
CLOSED
“ALERT”
OPEN
EXTERNAL SWITCH
CONNECTION BLOCK
ONBOARD REED SWITCH
LOCATION FOR
MAGNETIC SENSOR
EXTERNAL SWITCH
CONNECTION BLOCK
TAMPER SWITCH
ONBOARD
REED SWITCH
OPTION 1 MOUNTING
(DOUBLE SIDED FOAM TAPE)
OPTION 2 MOUNTING
VINYL ELECTRICAL
TAPE
19039 SCREW
(2) PROVIDED
KNOCK OUT FOR WIRES
OF EXTERNAL SWITCH
EXTERNAL SWITCH
CONNECTION BLOCK
TAMPER SWITCH
ONBOARD
REED SWITCH
APPROXIMATE GAP (1 INCH)
GAP MAY BE EFFECTED
IF MOUNTED ON METAL.
“RESTORE”
CLOSED
“ALERT”
CLOSED
“ALERT”
OPENED
APPROXIMATE GAP (1 INCH)
GAP MAY BE EFFECTED
IF MOUNTED ON METAL.
REED SWITCH CABLE
(18 INCHES)
APPROXIMATE GAP
(GREATER THAN 1 1/3 INCHES)
GAP MAY BE EFFECTED
IF MOUNTED ON METAL.
“ALERT”
“RESTORE”
“ALERT”
OPENED
APPROXIMATE GAP
(GREATER THAN 1 1/3 INCHES)
GAP MAY BE EFFECTED
IF MOUNTED ON METAL.
VINYL ELECTRICAL
TAPE
19039 SCREW
(2) PROVIDED
KNOCK OUT FOR WIRES
OF EXTERNAL SWITCH
J2
J1 J3
“RESTORE”
CLOSED
“ALERT”
OPEN
MAGNETIC SENSOR
“ALERT”
“RESTORE”
TILT SENSOR EXTERNAL TERMINALS
“RESTORE”
CLOSED
“ALERT”
OPEN
EXTERNAL SWITCH
CONNECTION BLOCK
ONBOARD REED SWITCH
LOCATION FOR
MAGNETIC SENSOR
EXTERNAL SWITCH
CONNECTION BLOCK
TAMPER SWITCH
ONBOARD
REED SWITCH
OPTION 1 MOUNTING
(DOUBLE SIDED FOAM TAPE)
OPTION 2 MOUNTING
VINYL ELECTRICAL
TAPE
19039 SCREW
(2) PROVIDED
KNOCK OUT FOR WIRES
OF EXTERNAL SWITCH
EXTERNAL SWITCH
CONNECTION BLOCK
TAMPER SWITCH
ONBOARD
REED SWITCH
Fig. 2
Fig. 3
Fig. 4