STI 34159 - Manual (Page 2)

— 2 —
Install batteries into the sensor transmitter
1. Remove the sensor transmitter cap by turning it counterclockwise.
2. WITHOUT PULLING ON THE BRASS ANTENNA OR ANY WIRES, grasp the outside of
the battery/circuit board holder by the finger notches, twist gently and pull out. Insert
two “C” alkaline batteries (not included).
3. Replace the battery holder/sensor transmitter and sensor transmitter cap.
4. To test or program sensor transmitter, place the sensor transmitter on a table or
counter approximately 5-10 ft. away from the receiver. Sensor transmitter can be
activated by rotating and will make a faint clicking noise to verify operation.
5. Sensor should be programmed to receiver before mounting outdoors. Refer to
receiver instructions for programming. (Model STI-34150 is factory programmed for
your convenience.)
Battery Powered (STI-34150 & STI-34151):
STI-30104
LAMP CONTROLLER
(OPTIONAL)
AC ADAPTER
GREEN
LED
TRANSISTOR
OUTPUT JACK
RECEIVER ANTENNA
SPEAKER
STI-34104
INDOOR RECEIVER
BUTTON
RED LED
SENSOR TRANSMITTER CAP
SENSOR TRANSMITTER BASE
MOUNTING
TUBE CAP
WALL MOUNT (INCLUDED)
NOT NEEDED FOR POLE
MOUNT INSTALLATION
2 “C” BATTERIES
(NOT INCLUDED)
SENSOR TRANSMITTER
12”MOUNTING TUBE
MOUNTING STAKE
SENSOR TRANSMITTER
BOTTOM
SENSOR TRANSMITTER
MOUNTING
TUBE CAP
MOUNTING STAKE
SENSOR TRANSMITTER BOTTOM
SCREWS
RECHARGEABLE NiMH BATTERIES
H L
SENSITIVITY JUMPERS
(SOLAR TYPE)
SENSITIVITY JUMPERS
(BATTERY TYPE)
H L
FINGER
NOTCHES
REMOVE PLASTIC TAB
FROM BATTERIES
DRIVEWAY
3’OR
LESS
25' OR MORE
PLACE SENSOR
TRANSMITTER 3' OR
LESS FROM EDGE OF
DRIVEWAY AND 25'
OR MORE FROM STREET.
12’
MAX
DRIVEWAY
PLACE SENSOR
TRANSMITTER 3' OR
LESS FROM EDGE OF
DRIVEWAY AND 25+
FEET OR MORE FROM
STREET.
25' OR MORE
3' OR
LESS
12'
MAX
+
+
-
B
DETAIL B
SCALE 2:1
B
C
H L
-
+
+
-
B
-
FINGER NOTCHES
DO NOT
PULL ANTENNA!
WALL MOUNT (INCLUDED)
NOT NEEDED FOR POLE
MOUNT INSTALLATION
SENSITIVITY
ADJUSTMENT
SENSITIVITY
ADJUSTMENT
POWER CONNECTOR ANTENNA CONNECTOR
12”MOUNTING TUBE
GREEN
LED
TRANSISTOR
OUTPUT JACK
RECEIVER ANTENNA
SPEAKER
BUTTON
RED LED
POWER CONNECTOR ANTENNA CONNECTOR
STI-30104
LAMP CONTROLLER
(OPTIONAL)
AC ADAPTER
GREEN
LED
TRANSISTOR
OUTPUT JACK
RECEIVER ANTENNA
SPEAKER
STI-34104
INDOOR RECEIVER
BUTTON
RED LED
SENSOR TRANSMITTER CAP
SENSOR TRANSMITTER BASE
MOUNTING
TUBE CAP
WALL MOUNT (INCLUDED)
NOT NEEDED FOR POLE
MOUNT INSTALLATION
2 “C” BATTERIES
(NOT INCLUDED)
SENSOR TRANSMITTER
12”MOUNTING TUBE
MOUNTING STAKE
SENSOR TRANSMITTER
BOTTOM
SENSOR TRANSMITTER
MOUNTING
TUBE CAP
MOUNTING STAKE
SENSOR TRANSMITTER BOTTOM
SCREWS
RECHARGEABLE NiMH BATTERIES
H L
SENSITIVITY JUMPERS
(SOLAR TYPE)
SENSITIVITY JUMPERS
(BATTERY TYPE)
H L
FINGER
NOTCHES
REMOVE PLASTIC TAB
FROM BATTERIES
DRIVEWAY
3’OR
LESS
25' OR MORE
PLACE SENSOR
TRANSMITTER 3' OR
LESS FROM EDGE OF
DRIVEWAY AND 25'
OR MORE FROM STREET.
12’
MAX
DRIVEWAY
PLACE SENSOR
TRANSMITTER 3' OR
LESS FROM EDGE OF
DRIVEWAY AND 25+
FEET OR MORE FROM
STREET.
25' OR MORE
3' OR
LESS
12'
MAX
+
+
-
B
DETAIL B
SCALE 2:1
B
C
H L
-
+
+
-
B
-
FINGER NOTCHES
DO NOT
PULL ANTENNA!
WALL MOUNT (INCLUDED)
NOT NEEDED FOR POLE
MOUNT INSTALLATION
SENSITIVITY
ADJUSTMENT
SENSITIVITY
ADJUSTMENT
POWER CONNECTOR ANTENNA CONNECTOR
12”MOUNTING TUBE
GREEN
LED
TRANSISTOR
OUTPUT JACK
RECEIVER ANTENNA
SPEAKER
BUTTON
RED LED
POWER CONNECTOR ANTENNA CONNECTOR
Sensitivity Adjustment:
The factory default setting (HIGH) may be adjusted by changing the jumper position inside the
sensor transmitter.
1. Unscrew cap.
2. Position the jumper to desired sensitivity (as shown).
• LOW: Position jumper on the two bottom pegs.
• MEDIUM: Completely remove jumper or hang on middle peg.
• HIGH: Position jumper on the two top pegs.
3. Replace cap.
STI-30104
LAMP CONTROLLER
(OPTIONAL)
AC ADAPTER
GREEN
LED
TRANSISTOR
OUTPUT JACK
RECEIVER ANTENNA
SPEAKER
STI-34104
INDOOR RECEIVER
BUTTON
RED LED
SENSOR TRANSMITTER CAP
SENSOR TRANSMITTER BASE
MOUNTING
TUBE CAP
WALL MOUNT (INCLUDED)
NOT NEEDED FOR POLE
MOUNT INSTALLATION
2 “C” BATTERIES
(NOT INCLUDED)
SENSOR TRANSMITTER
12”MOUNTING TUBE
MOUNTING STAKE
SENSOR TRANSMITTER
BOTTOM
SENSOR TRANSMITTER
MOUNTING
TUBE CAP
MOUNTING STAKE
SENSOR TRANSMITTER BOTTOM
SCREWS
RECHARGEABLE NiMH BATTERIES
H L
SENSITIVITY JUMPERS
(SOLAR TYPE)
SENSITIVITY JUMPERS
(BATTERY TYPE)
H L
FINGER
NOTCHES
REMOVE PLASTIC TAB
FROM BATTERIES
DRIVEWAY
3’OR
LESS
25' OR MORE
PLACE SENSOR
TRANSMITTER 3' OR
LESS FROM EDGE OF
DRIVEWAY AND 25'
OR MORE FROM STREET.
12’
MAX
DRIVEWAY
PLACE SENSOR
TRANSMITTER 3' OR
LESS FROM EDGE OF
DRIVEWAY AND 25+
FEET OR MORE FROM
STREET.
25' OR MORE
3' OR
LESS
12'
MAX
+
+
-
B
DETAIL B
SCALE 2:1
B
C
H L
-
+
+
-
B
-
FINGER NOTCHES
DO NOT
PULL ANTENNA!
WALL MOUNT (INCLUDED)
NOT NEEDED FOR POLE
MOUNT INSTALLATION
SENSITIVITY
ADJUSTMENT
SENSITIVITY
ADJUSTMENT
POWER CONNECTOR ANTENNA CONNECTOR
12”MOUNTING TUBE
GREEN
LED
TRANSISTOR
OUTPUT JACK
RECEIVER ANTENNA
SPEAKER
BUTTON
RED LED
POWER CONNECTOR ANTENNA CONNECTOR
Low Sensitivity Setting:
•
•
•
Jumper Location
Medium Sensitivity Setting:
•
•
•
Jumper Location
High Sensitivity Setting:
•
•
•
Jumper Location
STI-30104
LAMP CONTROLLER
(OPTIONAL)
AC ADAPTER
GREEN
LED
TRANSISTOR
OUTPUT JACK
RECEIVER ANTENNA
SPEAKER
STI-34104
INDOOR RECEIVER
BUTTON
RED LED
SENSOR TRANSMITTER CAP
SENSOR TRANSMITTER BASE
MOUNTING
TUBE CAP
WALL MOUNT (INCLUDED)
NOT NEEDED FOR POLE
MOUNT INSTALLATION
2 “C” BATTERIES
(NOT INCLUDED)
SENSOR TRANSMITTER
12”MOUNTING TUBE
MOUNTING STAKE
SENSOR TRANSMITTER
BOTTOM
SENSOR TRANSMITTER
MOUNTING
TUBE CAP
MOUNTING STAKE
SENSOR TRANSMITTER BOTTOM
SCREWS
RECHARGEABLE NiMH BATTERIES
H L
SENSITIVITY JUMPERS
(SOLAR TYPE)
SENSITIVITY JUMPERS
(BATTERY TYPE)
H L
FINGER
NOTCHES
REMOVE PLASTIC TAB
FROM BATTERIES
DRIVEWAY
3’OR
LESS
25' OR MORE
PLACE SENSOR
TRANSMITTER 3' OR
LESS FROM EDGE OF
DRIVEWAY AND 25'
OR MORE FROM STREET.
12’
MAX
DRIVEWAY
PLACE SENSOR
TRANSMITTER 3' OR
LESS FROM EDGE OF
DRIVEWAY AND 25+
FEET OR MORE FROM
STREET.
25' OR MORE
3' OR
LESS
12'
MAX
+
+
-
B
DETAIL B
SCALE 2:1
B
C
H L
-
+
+
-
B
-
FINGER NOTCHES
DO NOT
PULL ANTENNA!
WALL MOUNT (INCLUDED)
NOT NEEDED FOR POLE
MOUNT INSTALLATION
SENSITIVITY
ADJUSTMENT
SENSITIVITY
ADJUSTMENT
POWER CONNECTOR ANTENNA CONNECTOR
12”MOUNTING TUBE
GREEN
LED
TRANSISTOR
OUTPUT JACK
RECEIVER ANTENNA
SPEAKER
BUTTON
RED LED
POWER CONNECTOR ANTENNA CONNECTOR
Sensitivity Adjustment:
The factory default setting (HIGH) may be adjusted by changing the jumper position inside
the sensor transmitter.
1. Remove the bottom of the sensor transmitter by removing the 3 screws on the bottom
of the unit.
2. Position the jumper to desired sensitivity (as shown below).
• LOW: Position jumper on the two leftmost pegs.
• MEDIUM: Completely remove jumper or hang from middle peg.
• HIGH: Position jumper on the two rightmost pegs.
3. Replace the bottom of the unit and secure with the 3 screws.
Solar Powered (STI-34100 & STI-34101):
1. Remove the bottom of the sensor transmitter by removing the 3 screws on the
bottom of the unit.
2. Remove the plastic tab between the batteries.
3. Replace the bottom of the unit and secure with the 3 screws. Place the sensor
transmitter in direct sunlight for 48 hours.
OR
4. Place batteries in a NiMH (nickel metal hydride) battery charger (before using). Once
charged, return the batteries to the sensor transmitter. Replace the bottom and secure with the 3 screws.
5. To test or program sensor transmitter, place the sensor transmitter on a table or counter approximately 5-10 ft. away from
the receiver. Sensor transmitter can be activated by rotating and will make a faint clicking noise to verify operation.
6. Sensor should be programmed to receiver before mounting outdoors. Refer to receiver instructions for programming. (Model
STI-34100 is factory programmed for your convenience.)
Low Sensitivity Setting:
• • •
Jumper Location
Medium Sensitivity Setting:
Jumper Location
High Sensitivity Setting:
Jumper Location
• • • • • •
SENSOR
TRANSMITTER
CAP
SENSOR
TRANSMITTER
BASE
MOUNTING
TUBE CAP
WALL MOUNT (INCLUDED)
NOT NEEDED FOR POLE
MOUNT INSTALLATION
2 “C” BATTERIES
(NOT INCLUDED)
SENSOR TRANSMITTER
12” MOUNTING TUBE
MOUNTING STAKE
SENSOR
TRANSMITTER
BOTTOM
SENSOR
TRANSMITTER
MOUNTING
TUBE CAP
MOUNTING STAKE
SENSOR TRANSMITTER
BOTTOM SCREWS
RECHARGEABLE
NiMH BATTERIES
WALL MOUNT (INCLUDED)
NOT NEEDED FOR POLE
MOUNT INSTALLATION
+
+
-
B
-
SENSITIVITY
ADJUSTMENT
12” MOUNTING TUBE