STI 34108 - Manual

QUICK SETUP GUIDE
STI-34401 Universal Sensor
With 4-Channel Receiver
TO SETUP:
1. Open cover. Remove battery isolator strip.
2.
Configure jumpers - select one of the following: magnetic sensor, tilt sensor, external terminals.
3. Replace cover.
4. Program into receiver.
5. Mount where needed.
CONFIGURE JUMPERS:
PROGRAM 4-CHANNEL RECEIVER WITH SENSOR:
Please read this section completely before proceeding.
1. Plug antenna into the antenna (red) connector on the receiver.
2. Plug adapter into the wall.
3. While holding down the gray button, plug the adapter into the 4-Channel Receiver. A series of beeps/tones will begin playing. Release
button when beeps/tones finish. The red and green LED’s will flash quickly. The receiver is now in program mode and you have 1 minute to program
all sensors.
4. Activate a sensor to program into 4-Channel (refer to your sensor instructions). A tone or series of beeps will sound representing the channel the
sensor programmed into (i.e.: one beep is zone 1, two beeps is zone 2, etc.).
5. If more sensors are to be programmed, repeat step 4.
6. After programming sensor(s), wait a minimum of 5 seconds, press gray button to exit Program Mode or receiver will exit program mode automatically
within one minute.
CHECK SENSOR:
1. Trigger the sensor. Receiver will emit the alert tone and red light will flash. For multiple sensors, the receiver will beep a number of times (for the
number of the sensor, 1 through 4) and play the alert tone.
2. If red light flashes but there is no tone, the receiver is in silent mode. To exit silent mode press and hold the button until you hear a single beep
then release. Repeat step 6 to hear the receiver alert tone.
CLEAR SENSOR FROM 4-CHANNEL RECEIVER:
1. Disconnect power from receiver and wait approximately 15 seconds.
2. Reconnect power to the receiver, the receiver will make a start-up tone. The green LED will be solid.
3. Within 3 seconds press and hold down the gray button, you will hear a series of beeps/tones. When you hear a continuous tone, let go of the
button; the sensors are cleared.
For additional features and instructions refer to full instruction manual provided with your product.
APPROXIMATE GAP (1 INCH)
GAP MAY BE EFFECTED
IF MOUNTED ON METAL.
“RESTORE”
CLOSED
“ALERT”
CLOSED
“ALERT”
OPENED
APPROXIMATE GAP (1 INCH)
GAP MAY BE EFFECTED
IF MOUNTED ON METAL.
REED SWITCH CABLE
(18 INCHES)
APPROXIMATE GAP
(GREATER THAN 1 1/3 INCHES)
GAP MAY BE EFFECTED
IF MOUNTED ON METAL.
“ALERT”
“RESTORE”
“ALERT”
OPENED
APPROXIMATE GAP
(GREATER THAN 1 1/3 INCHES)
GAP MAY BE EFFECTED
IF MOUNTED ON METAL.
VINYL ELECTRICAL
TAPE
19039 SCREW
(2) PROVIDED
KNOCK OUT FOR WIRES
OF EXTERNAL SWITCH
J2
J1 J3
“RESTORE”
CLOSED
“ALERT”
OPEN
MAGNETIC SENSOR
“ALERT”
“RESTORE”
TILT SENSOR EXTERNAL TERMINALS
“RESTORE”
CLOSED
“ALERT”
OPEN
EXTERNAL SWITCH
CONNECTION BLOCK
ONBOARD REED SWITCH
LOCATION FOR
MAGNETIC SENSOR
EXTERNAL SWITCH
CONNECTION BLOCK
TAMPER SWITCH
ONBOARD
REED SWITCH
OPTION 1 MOUNTING
(DOUBLE SIDED FOAM TAPE)
OPTION 2 MOUNTING
VINYL ELECTRICAL
TAPE
19039 SCREW
(2) PROVIDED
KNOCK OUT FOR WIRES
OF EXTERNAL SWITCH
EXTERNAL SWITCH
CONNECTION BLOCK
TAMPER SWITCH
ONBOARD
REED SWITCH
APPROXIMATE GAP (1 INCH)
GAP MAY BE EFFECTED
IF MOUNTED ON METAL.
“RESTORE”
CLOSED
“ALERT”
CLOSED
“ALERT”
OPENED
APPROXIMATE GAP (1 INCH)
GAP MAY BE EFFECTED
IF MOUNTED ON METAL.
REED SWITCH CABLE
(18 INCHES)
APPROXIMATE GAP
(GREATER THAN 1 1/3 INCHES)
GAP MAY BE EFFECTED
IF MOUNTED ON METAL.
“ALERT”
“RESTORE”
“ALERT”
OPENED
APPROXIMATE GAP
(GREATER THAN 1 1/3 INCHES)
GAP MAY BE EFFECTED
IF MOUNTED ON METAL.
VINYL ELECTRICAL
TAPE
19039 SCREW
(2) PROVIDED
KNOCK OUT FOR WIRES
OF EXTERNAL SWITCH
J2
J1 J3
“RESTORE”
CLOSED
“ALERT”
OPEN
MAGNETIC SENSOR
“ALERT”
“RESTORE”
TILT SENSOR EXTERNAL TERMINALS
“RESTORE”
CLOSED
“ALERT”
OPEN
EXTERNAL SWITCH
CONNECTION BLOCK
ONBOARD REED SWITCH
LOCATION FOR
MAGNETIC SENSOR
EXTERNAL SWITCH
CONNECTION BLOCK
TAMPER SWITCH
ONBOARD
REED SWITCH
OPTION 1 MOUNTING
(DOUBLE SIDED FOAM TAPE)
OPTION 2 MOUNTING
VINYL ELECTRICAL
TAPE
19039 SCREW
(2) PROVIDED
KNOCK OUT FOR WIRES
OF EXTERNAL SWITCH
EXTERNAL SWITCH
CONNECTION BLOCK
TAMPER SWITCH
ONBOARD
REED SWITCH
Magnetic Sensor (supervised)
Tilt Sensor (supervised)
External Terminals (supervised)
Magnetic Sensor (not supervised)
Tilt Sensor (not supervised)
External Terminals (not supervised)
NOTE: To ensure jumpers do not reattach or short to other
components, cut both jumper leads flush to PCB and remove
jumper wire.
Cut jumpers with “X”, do not cut jumpers with “ .“
J1 J2 J3
X
X X
X
X X
X X X
Program sensor
before installation
12/12
STI-30104
LAMP CONTROLLER
(OPTIONAL)
AC ADAPTER
GREEN
LED
TRANSISTOR
OUTPUT JACK
RECEIVER ANTENNA
SPEAKER
STI-34104
INDOOR RECEIVER
BUTTON
RED LED
SENSOR TRANSMITTER CAP
SENSOR TRANSMITTER BASE
MOUNTING
TUBE CAP
WALL MOUNT (INCLUDED)
NOT NEEDED FOR POLE
MOUNT INSTALLATION
2 “C” BATTERIES
(NOT INCLUDED)
SENSOR TRANSMITTER
12”MOUNTING TUBE
MOUNTING STAKE
SENSOR TRANSMITTER
BOTTOM
SENSOR TRANSMITTER
MOUNTING
TUBE CAP
MOUNTING STAKE
SENSOR TRANSMITTER BOTTOM
SCREWS
RECHARGEABLE NiMH BATTERIES
H L
SENSITIVITY JUMPERS
(SOLAR TYPE)
SENSITIVITY JUMPERS
(BATTERY TYPE)
H L
FINGER
NOTCHES
REMOVE PLASTIC TAB
FROM BATTERIES
DRIVEWAY
3’OR
LESS
25' OR MORE
PLACE SENSOR
TRANSMITTER 3' OR
LESS FROM EDGE OF
DRIVEWAY AND 25'
OR MORE FROM STREET.
12’
MAX
DRIVEWAY
PLACE SENSOR
TRANSMITTER 3' OR
LESS FROM EDGE OF
DRIVEWAY AND 25+
FEET OR MORE FROM
STREET.
25' OR MORE
3' OR
LESS
12'
MAX
+
+
-
B
DETAIL B
SCALE 2:1
B
C
H L
-
+
+
-
B
-
FINGER NOTCHES
DO NOT
PULL ANTENNA!
WALL MOUNT (INCLUDED)
NOT NEEDED FOR POLE
MOUNT INSTALLATION
SENSITIVITY
ADJUSTMENT
SENSITIVITY
ADJUSTMENT
POWER CONNECTOR ANTENNA CONNECTOR
12”MOUNTING TUBE
GREEN
LED
TRANSISTOR
OUTPUT JACK
RECEIVER ANTENNA
SPEAKER
BUTTON
RED LED
POWER CONNECTOR ANTENNA CONNECTOR
4 CHANNEL RECEIVER