Anthro Security Cart 24 Assembly Instructions - Manual (Page 2)

Anthro ® Corporation Technology Furniture ® 10450 SW Manhasset Drive Tualatin, Oregon 97062
www.anthro.com
Nylon Lock Nut
325-5263-00
Cap Screw
325-5188-00
Step 1
Secure a Caster to a Caster Plate using four 3/4" Cap Screws
and Lock Nuts per Caster.
Repeat for remaining Casters, Caster Plates, Bolts, and Nuts.
Inside.Edge
(Green.Brake.Pedal)
Cap.Screw
Lock.Nut
Cap Screw
325-5188-00
Step 2
Place the Caster Plates with the Green Brake Pedals onto one
side of the Metal Base, sliding each Plate under the flanges on
the Metal Base. Secure using four Cap Screws.
Install the remaining Caster Plates on the other side.
Double-check the installation of the Swivel Lock Casters
(green brake pedal) by positioning the Caster Plates as shown.
Now depress the Brake. If it is installed correctly, the
Caster will be parallel with the Metal Base (as shown) .
3/4" Wood Screw
325-5106-00
Caster.Bracket.is..
positioned.BELOw..
the flange
Metal.Base.
flange
Rear.Edge.of.
Metal.Base.has.
four.small.holes.
along.edge..
Swivel.Lock.Casters
(Green.Brake.Pedal)
Swivel.Lock.Casters
(Green.Brake.Pedal)
Base Assembly
First
Next
Final
Barbs
Cart Assembly
Step 5
Loosely.attach the 24" Wide Shelf to the second hole from the
top (uncapped end) of each Vertical Leg using a Support Screw.
Next, align the two openings on each of the Panel Hangers with
those on the Shelf. Secure into place using two Wood Screws
through the Bracket into the Shelf.
Repeat for other Panel Hanger.
wood.Screw
Support Screw
325-5010-00
3/4" Wood Screw
325-5106-00 Support.Screw
24".wide.Shelf
Vertical.Legs
Step 6
Align one vertical leg so that the end with the Star Nut
inside is facing up. Loosely attach the 24" Wide Shelf to
the second hole down using a Support Screw.
Next, align each Panel Hanger with the pre-drilled holes
on the shelf. Secure in place using two Wood Screws.
Support Screw
325-5010-00
3/4" Wood Screw
325-5106-00
Side.Panel.Y
Support.Screw
Vertical.Leg
24".wide.Shelf
Side.Panel.X
Support.Screw
Support Screw
325-5010-00
3/4" Wood Screw
325-5106-00
wood.Screw
24".wide.Shelf
Step 7
Install the Side Panel X (with hinges) using the same
procedure described in Step 6.
Repeat for Side Panel X
(with hinges) .
Cap.Screw
Panel.Hanger
wood.Screw
Step 3
Slide the Plastic Corners between the Metal Base and
Caster Plates, securing with one 3/4" Wood Screw
through each Bracket into the Plastic Corners.
Hollow.side.
face.up
wood.Screw
Step 4
Attach four Shelf Supports to the Top Shelf. Begin by first
installing a Clamp into the Shelf notch. Be sure the pointed
Barbs face towards the outer Shelf edge.
Next slide a Shelf Support into the recesses of
the Clamp and Shelf. Push in as far as possible.
Finally, secure with a Clamp Screw
Clamp Screw
325-5086-00