Tennsco Electronic Workbench - Manual (Page 3)

10. OPTIONAL Riser Attachment
Standard Riser (Figure 1):
10a. Secure riser shelf (9) to supports using two
bolts and nuts on each end.
10b. Secure riser supports (8) to top end, using
four bolts and nuts (or four #14 wood screws
for wood tops).
Electronic Riser (Figure 5):
10a. Secure riser supports (8), to top end, using
four bolts and nuts (or four #14 wood screws
for wood tops).
10b. Install optional wiring kit into electronic riser
shelf (10) using instructions provided with
each wiring kit.
DO NOT CONNECT POWER TO UNIT
UNTIL ENTIRE UNIT IS ASSEMBLED.
NOTE: If wiring kit was not purchased,
proceed to step 10c.
10c. Align holes in flanges of wireway trough (11)
with holes in riser shelf. Insert four #10 sheet
metal screws and tighten.
10d. Secure electronic riser shelf (10) to
supports, using two bolts and nuts on each
end.
Riser to Riser:
10a. Secure riser supports to lower riser supports
with flange down, using four bolts and nuts.
10b. Secure riser shelf to supports using two
bolts and nuts on each end.
11. OPTIONAL Side and Back Rail Attachment
11a. Bolt side rail (12) to the right side of top end
attachment with four bolts and nuts (for wood
tops, use #14 wood screws and drill holes as
needed). Be sure that the rounded corners of
side rail are toward the front of the
workbench.
11b. Repeat step 11a to install rail for left side.
11c. Place back rail (13) across back and around
the outside of the side rails. Secure to bench
top with five bolts, nuts and washers. (For
wood tops use five #14 wood screws). Use
two bolts, nuts and washers at each end to
fasten to side rails.
Hard Maple Laminate Benchtop Maintenance:
Clean when necessary with warm water, soap or detergent.
Wipe dry immediately. Scouring powder, steel wool or
sandpaper can be used for stubborn stains and mars. Allow
a generous quantity of linseed oil or mineral oil to penetrate
all surfaces for five minutes before removing all excess oil.
Excessive dryness or humidity can cause cracks or
warping. Cracks should be filled with wood filler, sanded
smooth and re-oiled. Warping can be prevented by securely
attaching top to bench legs.
LIMITED WARRANTY
Tennsco warrants goods purchased hereunder to be free of
defects in materials and workmanship for a period of one (1) year
from the date of shipment, hereunder. This warranty shall not
apply in the event goods are damaged as a result of misuse,
abuse, neglect, accident, improper application, modification or
repair by persons not authorized by Seller, where goods are
damaged during shipment, or where the date stamps on the
goods have been defaced, modified or removed. UNLESS
CONSIDERED UNENFORCEABLE OR UNLAWFUL UNDER
APPLICABLE LAW:
a. ALL IMPLIED WARRANTIES, INCLUDING BUT NOT
LIMITED TO WARRANTIES OR MERCHANT ABILITY AND
FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY
EXCLUDED.
b. BUYERS REMEDY, IF ANY, FOR ANY DEFECTIVE GOODS
SHALL BE LIMITED TO A REFUND BY SELLER OR
REPLACEMENT OF THE GOODS AT SELLER’S OPTION,
AND SHALL IN NO EVENT INCLUDE DAMAGES OF ANY
KIND, WHETHER INCIDENTAL, CONSEQUENTIAL OR
OTHERWISE.
NO GOODS ACCEPTED FOR RETURN WITHOUT PRIOR
APPROVAL. Seller shall have the right to inspect any goods
claimed to be defective at Buyers place of business or require
Buyer to return the goods to Seller for inspection on Seller’s
premises. Transportation charges covering returned goods will
be borne by Seller only if such goods are proven to be defective,
are covered by this warranty and are returned within the warranty
period stated above.
TENNSCO CORPORATION
P.O. Box 1888
DICKSON, TN 37056-1888
(615) 446-8000 (800) 251-8184