Universal Air Tools UT8740C14 - 5 M14 - Manual

Read these instructions carefully before installing, operating,
servicing or repairing this tool. Keep these instructions in a safe
accessible place.
Important Operator Instructions
Includes - Foreseen Use, Work Stations, Putting Into Service, Operating,
Dismantling, Assembly and Safety Rules
Manufacturer/Supplier Product Type RPM
Cycles Per Min Universal Air Tool Company Limited
Unit 8
Lane End Industrial Park
High Wycombe
Bucks
HP14 3BY
Tel No Fax No (01494) 883300 (01494) 883237
Model No/Nos Serial No
Product Nett Weight
lbs
Kg
Recommended Use Of
Balancer Or Support
Recommended Hose Bore
Size - Minimum
Recommended Max.
Hose Length
Ins M/M Ft M
Foreseen Use of Tool
This right angle grinder is designed to be used with reinforced resin
bonded depressed centre grinding wheels that have a permitted
rotational speed in excess of 10,000 RPM. See parts lists for details of
available wheel sizes.
The tool is designed to be used for light grinding and dressing of welds,
etc. but not for cutting off. The grinder must never be used if a wheel
guard (disc cover) is not fitted.
Putting Into Service
Air Supply
Use a clean lubricated air supply that will
give a measured air pressure at the tool of
90 p.s.i./6.3 bar when the tool is running
with the trigger/lever fully depressed. Use
recommended hose size and length. It is
recommended that the tool is connected to
the air supply as shown in figure 1. Do not
connect the tool to the air line system
without incorporating an easy to reach and
Work Stations
The tool should only be used as a hand held hand operated tool. It is
always recommended that the tool is used when standing on a solid
floor. It can be used in other positions but before any such use the
operator must be in a secure position having a firm grip and footing and
be aware of the safety rules to be obeyed when using the grinder.
Angle Grinder
UT8740A10 - 4” M10
UT8740A14 - 4” M14
UT8740B14 - 4 1/2” M14
UT8740C14 - 5” M14
10,000
3/8 10 30 10 No
4.4
2.0
Page No 1
Noise Level Sound Pressure Level 83.0 dB(A)
Test Method Tested in accordance with Pneurop
test code PN8NTC1
Vibration Level
Test Method Tested in accordance with ISO
standard 8662
1.2 Metres / Sec²
Air Pressure
Recommended Working 6.3 bar 90 PSI
Recommended Minimum n/a bar n/a PSI
Maximum 7.0 bar 100 PSI
Personal Safety Equipment
Use - Safety Glasses Yes
Use - Safety Gloves Yes
Use - Safety Boots
Use - Breathing Masks
Yes
Use - Ear Protectors Yes
operate air shut off valve. The air supply should be lubricated. It is
strongly recommended that an air filter, regulator, lubricator (FRL) is
used as shown in Figure 1 as this will supply clean, lubricated air at
the correct pressure to the tool. Details of such equipment can be
obtained from your supplier. If such equipment is not used then the
tool should be lubricated by shutting off the air supply to the tool,
depressurising the line by pressing the trigger on the tool.
Disconnect the air line and pour into the intake bushing a
teaspoonful (5ml) of a suitable pneumatic motor lubricating oil
preferably incorporating a rust inhibitor. Reconnect tool to air supply
and run tool slowly for a few seconds to allow air to circulate the oil.
If tool is used frequently lubricate on daily basis and if tool starts to
slow or lose power.
It is recommended that the air pressure at the tool whilst the tool is
running is 90 p.s.i./6.3 bar. The tool can run at lower and higher
pressures with the maximum permitted working air pressure of
100 p.s.i./7 bar.