Universal Air Tools UT8771A - Manual

Manufacturer/Supplier Product Type
RPM
Cycles Per Min
Tel No Fax No
(01494) 883300 (01494) 883237
Model No/Nos Serial No
Product Nett Weight
lbs
Kg
Recommended Use Of
Balancer Or Support
Recommended Hose Bore
Size - Minimum
Recommended Max.
Hose Length
Ins M/M Ft M
Foreseen Use of Tool
The spindle thread on this tool is 7/16 dia x 20 TPI and is
designed to be used as a sander using 3”, 41/2” and 51/2” dia
backing pads with abrasive discs. Do not use the tool for any
other purpose than a sander. Do not fit any other type of pad or
abrasive or cutting device.
Work Stations
The tool should only be used as a handheld, hand operated tool.
It is always recommended that the tool is used when standing
on a solid floor. It can be used in other positions but before any
such use, the operator must be in a secure position having a
firm grip and footing and be aware of a reaction force on the
hand as result of the tool doing work.
No
Page No 1
Pistol Grip Sander
UT8771A
2.35
1.07
3/8 10 30 10
15,000
Includes - Foreseen Use, Work Stations, Putting Into Service,
Operating, Dismantling, Assembly and Safety Rules
Operator Instructions Important
Read these instructions carefully before installing, operating,
servicing or repairing this tool. Keep these instructions in a safe
accessible place.
Universal Air Tool Company Limited
Unit 8
Lane End Industrial Park
High Wycombe
Bucks
HP14 3BY
Vibration Level
Test Method
Tested in accordance with ISO
standards 8662 Parts 1 & 8
Less than 2.5
Noise Level
Sound Pressure Level 84.0 dB(A)
Test Method
Tested in accordance with Pneurop
test code PN8NTC1 and ISO Standard 3744
Metres / Sec²
Putting Into Service
Air Supply
Use a clean lubricated air supply
that will give a measured air
pressure at the tool of 90 p.s.i./
6.3 bar when the tool is running
with the trigger fully depressed.
Use recommended hose size
and length. It is recommended
that the tool is connected to the
air supply as shown in figure 1.
Do not connect the tool to the air
line system without incorporating
an easy to reach and operate air shut off valve. The air supply
should be lubricated. It is strongly recommended that an air
filter, regulator, lubricator (FRL) is used as shown in Figure 1 as
this will supply clean, lubricated air at the correct pressure to the
tool. Details of such equipment can be obtained from your
supplier. If such equipment is not used then the tool should be
lubricated by shutting off the air supply to the tool,
depressurising the line by pressing the trigger on the tool.
Disconnect the air line and pour into the intake bushing a
teaspoonful (5ml) of a suitable pneumatic motor lubricating oil
preferably incorporating a rust inhibitor. Reconnect tool to air
supply and run tool slowly for a few seconds to allow air to
circulate the oil. If tool is used frequently lubricate on daily basis
and if tool starts to slow or lose power.
It is recommended that the air pressure at the tool whilst the
tool is running is 90 p.s.i./6.3 bar. The tool can run at lower and
higher pressures with the maximum permitted working air
pressure of 100 p.s.i./7.0 bar.
Personal Safety Equipment
Use - Safety Glasses
Yes
Use - Safety Gloves
Yes
Use - Safety Boots
Use - Breathing Masks
Yes
Use - Ear Protectors
Yes
Air Pressure
Recommended Working
6.3
bar
90
PSI
Recommended Minimum
n/a
bar
n/a
PSI
Maximum
7.0
bar
100
PSI