AST AST4401 Datasheet - Manual (Page 2)

www.astsensors.com
TM
Electrical
A= 2 ft. (0.6m)
B= 4 ft. (1.2m)
C= 6 ft. (1.8m)
D= 10 ft. (3.0m)
E= Mini DIN 43650C
F= Packard Metripack 150 3-Pin
I= DIN 43650A
L= Conduit, Cable 2 ft. (0.6 m) +
M= Conduit, Cable 4 ft. (1.2 m) +
N= Conduit, Cable 6 ft. (1.8 m) +
P= Conduit, Cable 10 ft. (3 m) +
Y= M12x1 Eurofast
4 = Mini-Fast (CSA Only)
© 2014 American Sensor Technologies Inc. AST4401 06/18/2014.
All specifications subject to change without notice.
Ordering Information
Pressure Ranges +
Pressure Unit
B= Bar K= kg/cm 2 P= PSI
Outputs
1= 0.5-4.5V ratiometric
3= 1-5V
4= 4-20mA (2 wire loop powered)
6= 1-6V
Series Type
Pressure Measurement
Insert 5-digit pressure code
Options
000= No Options
AST4401 A 00500 P 4 1 000 L -SS
+ Also approved to UL/cUL 1604 Class 1 Div 1, Group A, B, C, D without requiring a barrier
Note: CSA approved products require case/earth ground electrical connection. See wiring installation sheet for further details
Approval
(Left Blank)= UL ANSI/ISA 12.12.01 Class I Div 1 Intrinsically Safe Groups A, B, C, D (formerly UL913)
-SS= Add “-SS” for CSA157 Class I Div 1 Grps C, D Intrinsically Safe and ANSI/ISA 12.27.01 Single Seal and SIRA ATEX Exia IIC Class I, Zone 0, T4
-Z= Add “-Z” for CRN Registered to ANSI/ASME B31.3. Contact factory for material, pressure, and process connection options (includes -SS approvals)
Wetted Material
0= 17-4PH
1= 316L
2= Inconel 718 (consult factory on availability)
4= Hastelloy C276 (consult factory on availability)
PSIG Measurement
-14.7 to 25**
Pressure Code
V0025**
BARG Measurement
-1 to 2**
Pressure Code
V0002**
0-25 00025 0-2 00002
0-50 00050 0-5 00005
0-100 00100 0-7 00007
0-150 00150 0-10 00010
0-200 00200 0-20 00020
0-250 00250 0-35 00035
0-500 00500 0-50 00050
0-1,000 01000 0-100 00100
0-2,500 02500 0-250 00250
0-5,000 05000 0-350 00350
0-7,500 07500 0-500 00500
0-10,000 10000 0-700 00700
CSA ONLY
0-15,000
CSA ONLY
15000
0-20,000 20000
+ Typical ranges. All ranges between 0-25 PSI and 0-20,000 PSI available.
**Compound ranges up to -14.7 to 500 PSI available. Please consult factory.
Process Connection
A= 1/4” NPT Male
B= 1/8” NPT Male*
C= 1/4” BSPP Male
F= 7/16”-20 UNF Male*
I= 1/4” NPT Female**
P= 1/2” MNPT**
W= F250C Female
Autoclave***
*Not available under 50PSI (not available in 316L) **Pressures up to 15,000 PSI
***Pressures from 10,000 to 20,000 PSI, not available in 316L