Edwards Signaling 5560M Series - Manual

P/N 3100792 ISSUE 1A © 2005
Cheshire, CT 06410 203-699-3300 (Ph)
203-699-3365 (Cust. Serv. Fax)
203-699-3078 (Tech. Serv. Fax)
Installation Instructions for Catalog Series 5560M
Mini-Mi TM Signal
Description and Operation
Edwards Catalog Series 5560M is an integrated communication
system designed to sound 55 system tones or one 20-second voice
message in factory, hallway, office and personnel areas. The Mini-
Mi is available either with or without a strobe. The Mini-Mi has
three modes of operation: stand-alone tone generation, stand-alone
voice generation and system audio operation. The Mini-Mi is in a
NEMA Type 3R enclosure and is UL and cUL Listed.
Five modules are available for use with the Mini-Mi.
INPUT POWER
Catalog Typical Current (A)
Number Voltage Standby Tone On
5560M-AQ 24V DC .03 .070
24V AC 50/60 Hz .08 .16
5560M-N5 120V AC 50/60 Hz .03 .088
5560MS-AQ 24V DC .03 .070
24V AC 50/60 Hz .08 .16
5560MS-N5 120V AC 50/60 Hz .03 .086
CAUTION: To prevent damage to the circuit and to otherwise assure
continued proper functioning, DO NOT operate the unit outside of the
Regulated 24V DC/FWR voltage range of 16 - 33V DC/V FWR.
Installation
Installation should be completed in accordance with either the Na-
tional Electrical Code or the Canadian Electrical Code, applicable
local codes.
1. Remove (4) screws from cover and remove cover. Mount
backplate on a 4" (102 mm) electrical box using (2) #8-32 x 5/8"
screws (provided) and (2) #8 steel washers (provided) or other
suitable hardware. For weatherproof applications, mount to
the Cat. No. 449 back box (purchased separately) using (4) #6-
32 x 3/4" screws (provided) and (4) #8 steel washers (provided)
or other suitable hardware.
CAUTION
During installation, take care not to damage
components on the printed circuit board.
3. Insert appropriate module, plugging it into the main board.
Secure to speaker using screws removed in step 2. (Figure1)
4. Connect green ground wire to earth ground.
Feed power source wires through the backplate and connect
to the unit's power source leads. Observe polarity for DC units.
For models with strobes, connect a second set of power source
wires to the strobe power leads.
5. Select the appropriate module from below and make
connections and settings as described below.
Audio Coupler Module Boards
Connect incoming 10V, 25V or 70V RMS audio line to AUD (+)
and AUD (-) as shown in Figure 2.
Place the audio voltage jumper on the appropriate audio voltage
(Figure 2).
Tone Module Boards
Set miniature programming switch on the printed circuit board
(Figure 3) for the desired tone. Refer to Table 2.
RS485 Activation
For models with RS485 activation, connect the RS485 wires to
terminals + TX/RX and - TX/RX on the module.
Set the dipswitch on the PC board for the appropriate baud rate
(Table 1) and address (Table 2) as shown in Figures 2 and 3.
Catalog Number Description
556A-M Audio Coupler Module
556A-M485 Audio Coupler Module with RS485 Connectivity
556T-M Tone Module
556T-M485 Tone Module Board with RS485 Connectivity
556V-M Voice Module
Electrical Specifications
2. Remove (2) screws holding pc board to speaker in the Mini-Mi
housing and remove pc board. (See Figure 1.)
WARNING
Do not apply power to the unit until installation is
completed and housing cover and outlet box cover are
secured.