Fire-Lite 411UDAC Dig C Digital Communica unicatortor User Manual

411ud

Advertising

Document #51123 Rev. A ECN 98-542 1/8/99

WARNING!

ARNING!

Do not allow trouble conditions to remain

Do not allow trouble conditions to remain
logged in the system. Protection that the

logged in the system. Protection that the

logged in the system. Protection that the
system off

system off

system offers has been compromised, or

ers has been compromised, or

eliminated when a trouble condition exists.

Frame and mount adjacent to the control panel.

411UD

411UDA

AC Dig

C Dig

C Digital Comm

ital Comm

ital Communica

unica

unicator

tor

Oper

Opera

aating Instr

ting Instr

ting Instructions

uctions

NORMAL

NORMAL - Only the green AC POWER LED is on. All other
LEDs are off.

PANEL

ANEL

ANEL - The key to open the panel can be found at this

location.

WHEN AUDIBLE DEVICES ARE SOUNDING -

WHEN AUDIBLE DEVICES ARE SOUNDING -
F

For an Alar

or an Alar

or an Alarm:

1) Evacuate the protected area.
2) Notify the monitoring service and/or the Fire Department

immediately. Tell them briefly what happened and what
your current status is.

3) If the Fire Department is responding, be prepared to

provide directions to arriving firefighters.

For

or T

Troub

roub

rouble Only:

le Only:

1) Notify the monitoring service and/or Fire Department if this

panel is connected to either one, and tell them what is
happening.

2) Silence audible devices by unlocking and opening the

panel and pressing the ACK/SILENCE key once. The
yellow TROUBLE LED will remain on. Contact authorized
service personnel immediately! (Refer to Local Service
Representative block below).

To retur

o retur

o return to nor

n to nor

n to normal after an alar

mal after an alar

mal after an alarm:

1) Do not enter the protected area until safe to do so.
2) Clear all initiating devices. Smoke detectors will realarm if

there is still smoke in the area.

3) Reset the control panel being monitored by the 411UDAC

or, if being used as a stand-alone fire alarm communicator
(with approval of Authority Having Jurisdiction), press the
411UDAC RESET key.

Alar

Alarm Silencing

m Silencing

m Silencing - Notification Appliance circuit may be

silenced by pressing the ACK/SILENCE key a second time,
holding it for a minimum of two seconds. Subsequent alarms
will reactivate circuits. Press the RESET key to clear the
silenced condition.
NOTE: Alarm silencing may be disallowed for 1 minute if
programmed (see manual).

Power failure or brownout

Power failure or brownout - AC POWER LED will extinguish
for AC fail or brownout and the SYSTEM TROUBLE LED will
turn on. The local panel sounder and SYSTEM TROUBLE
LED will turn on for either condition and any other audible
trouble devices will sound. Contact authorized service
personnel immediately. (Refer to Local Service Representa-
tive block to the right).

Refer to the 411UDAC Technical Manual
P/N 51073 for more details.

Local Service Representative

Name:_________________________

Address:_______________________

Telephone:_____________________

To test the lamps, connect the optional
Fire•Watch 411 Series DACT Programmer
(Model PRO-411) and press:

LAMP
TEST

INSTRUCTIONS

To clear alarm indications in 411UDAC
after cause of alarm has been corrected,
reset the control panel being monitored by
the 411UDAC.

If 411UDAC is being used as a fire alarm
control panel (with the permission of the
Authority Having Jurisdiction), clear alarm
indications in the 411UDAC by pressing :

To silence the local panel sounder, press:

ACK/SILENCE

RESET

To silence the 411UDAC Notification
Appliance Circuit, press:

ACK/SILENCE

a second time and hold a
minimum of two seconds.

Advertising

Popular Brands

Popular manuals