GEAR4 StreetParty Wireless 2 - Manual (Page 2)

User Manual | StreetParty Wireless 2 | GEAR4 2
Please read before use.
Copyright © 2014 Disruptive Hong Kong Limited. All rights reserved. Reproduction in part or in whole is
prohibited. GEAR4 and StreetParty Wireless 2 are trade marks of Disruptive Hong Kong Limited. iPhone and
iPod touch are trade marks of Apple Inc., registered in the U.S. and other countries. iPad is a trade mark of
Apple Inc. App Store is a service mark of Apple Inc.
The Bluetooth® word mark and logos are registered trademarks of Bluetooth SIG, Inc.
Disruptive Hong Kong declares that this portable speaker [PS013] is in compliance with the essential
requirements and other relevant provisions of Directive 1999/5/CE. It’s possible for you to download a
complete copy of this declaration on the website www.gear4.com/DOC.
Instructions for use
Installing the battery
■ Open the battery compartment and place a
rechargeable battery into the base of the
speaker, following the polarity markings (
+/–). Guidelines for this are marked on the
base of the battery compartment.
Powering On
■ Slide the On/Off switch to the “ON” position,
the Blue LED will start to flash. The SPW2
will automatically enter Bluetooth mode when
powered on. If an Aux (3.5 mm) cable is
connected to the SPW2, the Blue LED will
not illuminate. Please note: When the SPW2
is in Aux-In mode the Bluetooth mode will be
disconnected.
Powering Off
■ Slide the On/Off switch to the “OFF” position,
all the LED status lights will shut off.
Bluetooth Mode
PAIRING
■ The unit will automatically go into “Pairing
Mode” when it is powered on. Go into your
devices settings menu and look for “GEAR4
SPW2”. After the unit has paired, it will
connect automatically when the SPW2 is
powered on and the device is in range.
PLAYING MUSIC
■ Press to start playing music.
■ Press either “–” or “+” for volume control.
MAKING AND RECEIVING PHONE CALLS
■ When the SPW2 is connected and paired to
your device the SPW2 allows you to make or
receive phone calls with its built-in
microphone.
■ Press to accept a call.
■ To hang up a call press .
■ To reject a call, press and hold the .
Aux-In Mode
■ Plug in the supplied 3.5 mm cable into the
SPW2. The other end is connected to your
device.
Charging
■ Attach the USB cable to the SPW2, and plug
in to any USB charger. If the unit is
completely discharged, it will take
approximately 2.5 hours to fully charge. The
Red LED will illuminate during charging,
when it has completed it will turn Green.
LED Status
Bluetooth pairing Mode:
Green LED & flashing Blue LED
Bluetooth connected Mode:
Green LED & solid Blue LED
Aux Mode: Green LED only
Charging: Red LED
11
5
6
9
10
7
1
8
4
3
2
1 On/off button
2 Working indicator light (green)/charge
indicator light (red)
3 MIC
4 Bluetooth indicator light (blue)
5 Pause/Play
6 Press for volume –
7 Press for volume +
8. Hands free answer / Hands free hang up
9. USB DC 5V
10. Aux-in
11. Battery cover
• Stream music from any Bluetooth device*
• Removable and rechargeable lithium-ion
battery
• Speakerphone
• Up to 5 hours’ battery life**
• Aux-in port for use with other music players
• Micro-USB charging
• Soft touch finish
• Stereo sound
• Passive radiator for enhanced bass
*Bluetooth 3.0 (A2DP) range up to 10m, depending on line of sight.
**Battery life at maximum volume
Register your StreetParty Wireless 2 to activate your warranty and receive product updates at
www.gear4.com/register