B.7 calibrate:subnetmask command, B.8 calibrate:subnetmask? query, B.9 calibrate:gatewayadd command – KEPCO EL Series Electronic Load Operator Manual P/N 243-1295 Firmware Version 3.22 through 3.41 User Manual
Page 63: B.10 calibrate:gatewayaddress? query, B.11 calibrate:gpib command, B.12 calibrate:gpib? query, B.13 calibrate:dnsadd command, B.14 calibrate:dnsadd? query, Calibrate:subnetm, Calibrate:g
SERIES EL 062011
B-3
B.7
CALibrate:SUBNetmask COMMAND
CAL:SUBN
Syntax:
Short Form: CAL:SUBN <a.b.c.d>
Long Form: CALibrate:SUBNetmask <a.b.c.d>
Where: <a, b, c, d> = numbers from 0 to 255 comprising the Subnet Mask
Description: Sets the Subnet Mask to be used during LAN communication.
B.8
CALibrate:SUBNetmask? QUERY
CAL:SUBN?
Syntax:
Short Form: CAL:SUBN?
Long Form: CALibrate:SUBNetmask?
Returns: <a.b.c.d> = numbers from 0 to 255 comprising the Subnet Mask
Description: Returns the Subnet Mask used during LAN communication.
B.9
CALibrate:GATEwayadd COMMAND
CAL:GATE
Syntax:
Short Form: CAL:GATE <a.b.c.d>
Long Form: CALibrate:GATEwayadd <a.b.c.d>
Where: <a, b, c, d> = numbers from 0 to 255 comprising the Gateway Address.
Description: Sets the Gateway Address to be used during LAN communication.
B.10 CALibrate:GATEwayaddress? QUERY
CAL:GATE?
Syntax:
Short Form: CAL:GATE?
Long Form: CALibrate:GATEwayaddress?
Returns: <a.b.c.d> = numbers from 0 to 255 comprising the Gateway Address
Description: Returns the Gateway Address used during LAN communication.
B.11 CALibrate:GPIB COMMAND
CAL:GPIB
Syntax:
Short Form: CAL:GPIB <NR1>
Long Form: CALibrate:GPIB <NR1>
Where: <NR1> = numbers from 1 to 30 comprising the GPIB Address. Factory default GPIB address
is 10.
Description: Sets the GPIB Address to be used during communication over the GPIB interface. After setting
the address, the EL Load must be power cycled (turned off, then on) in order for the new GPIB
address to take effect. Command is not valid from the GPIB interface.
B.12 CALibrate:GPIB? QUERY
CAL:GPIB?
Syntax:
Short Form: CAL:GPIB?
Long Form: CALibrate:GPIB?
Returns: <NR1> = number from 1 to 30 comprising the GPIB Address
Description: Returns the GPIB Address used during communication over the GPIB interface. Command is
not valid from the GPIB interface.
B.13 CALibrate:DNSadd COMMAND
CAL:DNS
Syntax:
Short Form: CAL:DNS <a.b.c.d>
Long Form: CALibrate:DNSadd <a.b.c.d>
Where: <a, b, c, d> = numbers from 0 to 255 comprising the DNS Address.
Description: Sets the Gateway Address to be used during LAN communication.
B.14 CALibrate:DNSadd? QUERY
CAL:DNS?
Syntax:
Short Form: CAL:DNS?
Long Form: CALibrate:DNSadd?
Returns: <a.b.c.d> = numbers from 0 to 255 comprising the DNS Address
Description: Returns the DNS Address used during LAN communication.