NOSHOK 2100 Series Field Upgradeable Dual Input Process Indicator User Manual
Page 24
24
1
For Input Registers, replace the 4xxxx with a 3xxxx in the above register address. The 3xxxx are a mirror of the 4xxxx Holding Registers.
2
An attempt to exceed a limit will set the register to its high or low limit value.
Calculation Display Rounding Factor
Calculation Filter Band
A=Input A, B=Input B, C=Calculation Constant
0=1 Rdg/sec, 1=2 Rdgs/sec, 2=5 Rdgs/sec,
3=10 Rdgs/sec, 4=20 Rdgs/sec
1=1 Display Unit
1=1 Display Unit
0=Auto, 1=Latch1, 2=Latch2
0=Auto, 1=Latch1, 2=Latch2
Read/Write
Read/Write
Read/Write
Read/Write
2
2
0
0
65000
65000
2
2
1
1
0
0
0=Max Update Rate, 1=0.1 sec
0=Max Update Rate, 1=0.1 sec
SEE MODULE 6 FOR DESCRIPTION OF PARAMETERS
(APPLIES ONLY IF SP OPTION CARD, IS INSTALLED)
Hysteresis
Hysteresis
Reset
Reset
40363
40373
40367
40377
1=0.1 Second
1=0.1 Second
0=No, 1 = Yes
0=No, 1 = Yes
0=Second, 1=Minute, 2=Hour, 3=Day
Read/Write
0=Off, 1=On
0=0, 1=0.0, 2=0.00, 3=0.000, 4=0.0000
1=0.1 Second
0=1, 1=2, 2=5, 3=10, 4=20, 5=50, 6=100
1=1 display unit
0=A-Rel, 1=A-Abs, 2=b-Rel, 3=bAbs, 4=Calc
0=A-Rel, 1=A-Abs, 2=b-Rel, 3=bAbs, 4=Calc
Read/Write
Read/Write
Read/Write
Read/Write
0
0
0
0
32750
32750
1
1
0
0
0
0
On Delay
On Delay
Standby
Standby
40364
40374
40368
40378
1=0.1 Second
1=0.1 Second
0=Off, 1=Normal, 2=Reverse, 3=Flash
0=Off, 1=Normal, 2=Reverse, 3=Flash
Read/Write
Read/Write
Read/Write
Read/Write
0
0
1
1
32750
32750
3
3
0
0
1
0
Off Delay
Off Delay
Lit - Annunciator
Lit - Annunciator
40365
40375
40369
40379
Read/Write
Read/Write
10
10
32750
32750
0
0
Max (Hi) Capture Delay Time
Min (Lo) Capture Delay Time
40332
40334
SETPOINT 1 OUTPUT PARAMETERS
Note: SP Values are located at Registers 40013-40021
SETPOINT 2 OUTPUT PARAMETERS
Read/Write
Read/Write
0
0
6
6
0
0
Assignment
Assignment
40361
40371
0=No, 1=Ab-HI, 2=Ab-Lo, 3=AU-HI, 4=AU-LO,
9=totLo, 10=totHI; Do not use 5-8.
0=No, 1=Ab-HI, 2=Ab-Lo, 3=AU-HI, 4=AU-LO, 5=dE-HI,
6=dE-LO, 7=bANd, 8=bNdIn, 9=totLo, 10=totHI
0=Normal, 1=Reverse
0=Normal, 1=Reverse
Read/Write
Read/Write
Read/Write
Read/Write
0
0
0
0
10
10
1
1
0
0
0
0
Action
Action
Output Logic
Output Logic
40362
40372
40366
40376
1
3
0
Total Timebase
40353
1=0.001
Read/Write
1000
65000
0
Total Scale Factor
40354
Read/Write
-19999
99999
-19999
Total Low Cut Value (Hi word)
40355
0 = No, 1 = Yes
Read/Write
Read/Write
-19999
0
99999
1
-19999
0
Total Low Cut Value (Lo word)
Total Reset at Power Up
40356
40357
TOTALIZER PARAMETERS
0=A-Rel, 1= b-Rel, 2= Calc
Read/Write
0
2
0
Total Assignment
40351
0=0, 1= 0.0, 2=0.00, 3=0.000, 4=0.0000
Read/Write
2
4
0
Total Decimal Point
40352
Read/Write
Read/Write
Read/Write
Read/Write
Read/Write
Read/Write
0
3
10
1000
0
10
1
4
250
99999
6
250
0
0
0
-19999
0
0
Units Annunciator Backlight
Calculation Display Decimal Point
Calculation Constant Value Low
Calculation Display Filter Value
Calculation Constant Value High
40336
40338
40340
40342
40339
40341
40343
Read/Write
Read/Write
0
0
4
5
0
0
Display Update Time
Calculation Function
40335
40337
Read/Write
Read/Write
0
0
4
4
0
0
Max (Hi) Value Assignment
Min (Lo) Value Assignment
40331
40333
SECONDARY PARAMETERS (Continued)
SEE MODULE 4 FOR DESCRIPTIONS OF PARAMETERS
COMMENTS
ACCESS
FACTORY
SETTING
HIGH LIMIT
2
LOW LIMIT
2
REGISTER NAME
REGISTER
ADDRESS
1
0 = C+A+B
1 = C-A-B
2 = C+A-B
3 = A*B/C
4 = C*A/B
5 = C*(1-A/B)
0=None
1=A-Rel
2=A-Abs
3=b-Rel
4=b-Abs
5=Calc
6=Tot
6=Tot
5=Calc
4=b-Abs
3=b-Rel
2=A-Abs
1=A-Rel
0=None