SHIMPO DT-205L - Manual (Page 4)

INSTRUMENTS INSTRUMENTS INSTRUMENTS INSTRUMENTS INSTRUMENTS 1701 Glenlake Avenue Itasca, IL 60143 · phone: (800) 237-7079 · fax: (630) 924-0342 · www.shimpoinst.com
DIMENSIONS AND SPECIFICA DIMENSIONS AND SPECIFICA DIMENSIONS AND SPECIFICA DIMENSIONS AND SPECIFICA DIMENSIONS AND SPECIFICATIONS TIONS TIONS TIONS TIONS
WARRANTY WARRANTY WARRANTY WARRANTY WARRANTY
LIMITED EXPRESS WARRANTY: Shimpo Instruments warrants, to the original purchaser of new products only, that this product shall be
free from defects in workmanship and materials under normal use and proper maintenance for one year from the date of original purchase.
This warranty shall not be effective if the product has been subject to overload, misuse, negligence, or accident, or if the product has been
repaired or altered outside of Shimpo Instruments’s authorized control in any respect which in Shimpo Instruments’s judgment, adversely
affects its condition or operation.
DISCLAIMER OF ALL OTHER WARRANTIES: The foregoing warranty constitutes the SOLE AND EXCLUSIVE WARRANTY, and Shimpo
Instruments hereby disclaims all other warranties, expressed, statutory or implied, applicable to the product, including, but not limited to all
implied warranties of merchantability and fitness.
LIMITATION OF REMEDY: Under this warranty, Shimpo Instruments’ SOLE OBLIGATION SHALL BE TO REPAIR OR REPLACE the defective
product or part, at Shimpo Instruments’ option. Shimpo Instruments reserves the right to satisfy warranty obligation in full by reimbursing
Buyer for all payments made to Shimpo Instruments, whereupon, title shall pass to Shimpo Instruments upon acceptance of return goods. To
obtain warranty service, Purchaser must obtain Shimpo Instruments’s authorization before returning the product, properly repackaged, freight
pre-paid to Shimpo Instruments.
INDEMNIFICATION & LIMITATION OF DAMAGES: Buyer agrees to indemnify and hold Shimpo Instruments harmless from and against all
claims and damages imposed upon or incurred arising, directly or indirectly, from Buyer’s failure to perform or satisfy any of the terms described
herein. In no event shall Shimpo Instruments be liable for injuries of any nature involving the product, including incidental or consequential
damages to person or property, any economic loss or loss of use.
MERGER CLAUSE: Any statements made by the Seller’s representative do not constitute warranties except to the extent that they also appear
in writing. This writing constitutes the entire and final expression of the parties’ agreement.
MODEL DT-205L
Display Range 6 to 99,999 rpm
Accuracy ±1 rpm: 6 to 8,300 rpm
±2 rpm: 8,300 to 25,000 rpm
25,000 to 99,999 rpm: ±0.006% of reading ±1 digit (±6 rpm max.)
Display 5 digit 0.47" (12mm) high LCD
Measuring Units RPM (on contact using adapter, included)
For YPM, mPM, FPM, IPM and Length: YRD, m, FT and IN
use 6" cir. wheel with 200L adapter
Measuring Distance 14' (4.2 m) maximum
Memory System 13 readings are stored in memory and retained for 5 minutes
(last, max., min. and 10 extra measurements)
Detection Laser diode / contact
System Control Single chip C-MOS microprocessor
Over Range Indicator Flashing numerals
Update Time 1 second (typical)
Batteries Included Size: 2 AA 1.5V
Life: Approx. 40 hrs
Low Voltage Indicator Flashing “LO BAT” display
Operating Temperature 32° to 113°F (0° to 45°C)
Construction
Die-cast aluminum housing
Weight 0.8 lb (365g)
Dimensions 6.6"L x 2.4"W x 1.8"H (167.5 mm x 60 mm x 46 mm)
Warranty 1 year
Standard Accessories Reflective tape, 2 cone adapters, 1 funnel adapter, NIST
certificate, instruction manual, carrying case, 200L adapter,
master wheel (6" cir.) and 3.5" extension shaft
TROUBLESHOOTING TROUBLESHOOTING TROUBLESHOOTING TROUBLESHOOTING TROUBLESHOOTING
The following are general checkpoints; please call your local Shimpo representative or contact Shimpo Instruments directly
for further assistance.
No laser beam is evident:
• Confirm that power switch is functioning
• Confirm that batteries are functioning and that polarity is correct
Inaccurate measurement results:
• If the surface being measured is highly reflective, it may need to be painted a darker color in order to ensure reliable results
• Beam may not be hitting the reflective tape, or taped area may be too small
• Measuring distance may be too short (unit must be at least 5” from intended mark)
Copyright © Nidec-Shimpo America Corporation 2003. All rights reserved. Product specifications are subject to change without notice.