Advanced Protection BNCB5kA - Manual

(800) 237-4567 · (727) 535-6339 · Fax (727) 539-8955
www.aptsurge.com · [email protected]
Advanced Protection Technologies, Inc.
14550 58th Street North, Clearwater, Florida 33760
SPD SPD
SPD
SPD
BUILD ING
S ECOND AR Y S PD
PR IMAR Y S PD
COAX CABLE
Secondary SPD
(UL 497A) with better
clamping performance
to better protect
Primary SPD
(UL 497C) for life safety
purposes to protect
against Power line cross
or direct stroke
Protecting Coax Cables from Surges
Most surges on coax cable originate on the shield, not the pin.
• In a coax application, the pin is protected by the shield. For
example, lightning induces onto the shield, as would accidental
contact with a power line. Consequently, excessive emphasis on
protecting the pin may be misguided.
• According to IEEE C62.43 research:
– Surge current injected equally onto the pin and shield will
propagate unequally. Due to inductance, the shield will carry
about four times more surge current than the pin.
• “Surge propagation speed is faster on the shield than the pin,
leading to voltage differentials between pin and shield on long
runs of coax cable.”
• Coax surge protection is different than AC power surge protection:
– Focus is on the grounded shield conductor as opposed to the
‘active’ conductor. (On AC systems, focus is usually on the
energized conductor.)
– MOV suppression components may degrade signal quality due to
higher capacitance.
Primary & Secondary SPDs are intended for use together in a
cascade arrangement.
• Irony: People routinely protect AC circuits with sizeable cascade
SPDs, but do not do it with coax, despite smaller SPDs and
sometimes a harsher environment. Cascade SPDs as appropriate.
UL 497 Listing categories are often misunderstood.
• UL has two generalized categories for Communication SPDs:
Primary and Secondary Protectors.
– Primary Protectors: e.g., UL 497, UL 497C. “Primary protectors
are intended to suppress abnormal overvoltage conditions that
may exist on the circuit due to accidental contact with electric
light or power conductors operating at or over 300 V to ground…”.
Translation: These are more intended for life safety protection
from power line crosses & lightning, and may not clamp low
enough to protect sensitive electronics.
– Secondary Protectors: e.g., UL 497A. “Secondary protectors are
intended to suppress abnormal voltage and/or current conditions
that bypass the primary protector.”
Translation: Secondary Protectors offer better clamping
protection for sensitive electronics.
• Hiccup?: There are single SPDs having the robust componentry
of Primary SPDs and the lower and better clamping performance
of Secondary SPDs. However, by quirk, the lower clamping
voltage and better performance prevents them from passing
UL’s testing as a Primary Protector. The resulting confusion
factor is one reason why various manufacturers do not UL List
coax SPDs. Note that UL 96A Lightning Protection applications
mandate a UL 497C unit. Good practice suggests an additional
Secondary Protector to protect sensitive electronics.
Hiccup: Ground Loops and resulting signal loss
• Coax cable shields are grounded at their ‘head-end’. The shield is
not supposed to be grounded further downstream. Reason: If the
shield is grounded at multiple locations, and those grounds are at
different potentials, then current will ‘loop’ through the shield as the
ground potentials attempt to equalize themselves. This is called a
Ground Loop, and can/will cause signal decay.
• Away from the ‘head-end’, if the SPD’s shield protection is directly
connected to ground, it can/will cause a ground loop. Different SPD
technology with ground isolation is required to prevent this. The APT
SPD will not cause ground loops.
Concept of Cascade Protection
Avoiding Ground Loops
SPD
SPD
If these two grounds have a voltage difference, and
the coax Shield can complete the circuit, then current
will flow through the Shield creating a Ground Loop.
COMMUNICATION
EQUIPMENT
Head-End Coax
Shield is Referenced
to Ground
If remote SPD shield is ‘hard-grounded’ and there
is a voltage between the two grounds, then a
Ground Loop is likely. An SPD with ground
isolating qualities is required (APT BNCA10kA).
COAX CABLE
05.29.14.jb