Blue Angel Pumps SEF40D-2 - Manual

This pump is intended for use in
domestic sump or effluent lift stations.
It is suitable for pumping effluent,
wastewater, ground water and other
nonexplosive, noncorrosive liquids
with up to 1/2" solids.
Sump /
effluent
pump will not pump raw sewage or
any substance exceeding 1/2” size.
This
pump is
not designed to handle salt water,
brine, laundry discharge, or any other
application which may contain caustic
chemicals and/or foreign materials.
Pump damage could occur if used in
these applications and will void
warranty.
Unpacking
Inspect this unit before it is used.
Occasionally, products are damaged
during shipment. If the pump or
components are damaged, return the
unit to the place of purchase for
replacement. Failure to do so could
result in serious injury or death.
GALLONS PER MINUTE
AT TOTAL HEAD IN FEET
Model 10 15 20 25
SEF40 41 29 14 0
Please read and save these instructions. Read carefully before attempting to assemble,
install, operate or maintain the product described. Protect yourself and others by
observing all safety information. Failure to comply with instructions could result in
personal injury and/or property damage! Retain instructions for future reference.
Description
A sump/effluent system consists of a
pump, control switch and a basin.
The system may be controlled by a
float switch with one of the following
kinds of plugs:
Models SEF40D, SEF40D-2, SEF40V,
SEF40V-2, SEF40T, and SEF40T-2:
piggyback-style plug (which accepts
the pump plug) or
Model SEF40M: standard plug (which
uses internal wiring)
The system will use one of the
following kinds of switches:
Models SEF40V and SEF40V-2:
Vertical Mechanical Switch;
Models SEF40T and SEF40T-2:
Mechanical Float Switch; or
Models SEF40D and SEF40D-2:
Diaphragm Switch
Operating Instructions SEF40V, SEF40V-2, SEF40T, SEF40T-2,
and Parts Manual SEF40D, SEF40D-2, SEF40M
330405-002 12/07 © 2007 Blue Angel™ Pumps
The Professional’s Line
Sump / Effluent Pump
Rating 4/10 HP, 8.3 A 4/10 HP, 8.3 A 4/10 HP, 8.3 A 4/10 HP, 8.3 A
Switch Vertical 90 o Wide Angle Diaphragm Manual
Mechanical Mechanical Switch Operation
Switch Float Switch
Cut-in level (factory set) 7.5" 12.5” 12" —
Cut-out level (factory set) 3.5" 4” 4.5" —
SEF40V SEF40T SEF40D SEF40M
REMINDER: Keep your dated proof of purchase for warranty purposes!
Attach it to this manual or file it for safekeeping.
Safety Guidelines
This manual contains information that
is very important to know and
understand. This information is
provided for SAFETY and to PREVENT
EQUIPMENT PROBLEMS. To help
recognize this information, observe the
following symbols.
Danger
indicates
an imminently hazardous situation
which, if not avoided, WILL result in
death or serious injury.
Warning
indicates
a potentially hazardous situation
which, if not avoided, COULD result in
death or serious injury.
Caution
indicates
a potentially hazardous situation
which, if not avoided, MAY result in
minor or moderate injury.
Notice
indicates
important information, that if not
followed, MAY cause damage to
equipment.
For parts, product & service information
visit www.blueangelpumps.com
Specifications
Power supply
requirements . . . . . . . . . . .120V, 60 hz
Circuit requirements . . . . .15 amps (min)
Motor duty . . . . . . . . . . . .Intermittent
Motor . . . . . . . . . . . . . . . .120V, 1 Phase,
3000RPM
Liquid temperature
range . . . . . . . . . . . . . . . . .40°F to 125°F
Max. operating position . .45
o from
vertical
Dimensions . . . . . . . . . . . .9" x 10"
Discharge . . . . . . . . . . . . . .1-1/2"
Power cord . . . . . . . . . . . .18 gauge
3 conductor
w/plug
Construction
Pump housing................Cast iron
Impeller..........................Glass reinforced
ABS
Inlet Cover .....................Stainless Steel
Shaft seal .......................Rubber Shaft Seal
Performance
Performance Curve