Dwyer TP2 - Manual

Series TP2 Thermocouple Thermometers
Specifications - Installation and Operating Instructions
TE-TP2
DWYER INSTRUMENTS, INC.
Phone: 219/879-8000 www.dwyer-inst.com
P.O. BOX 373 • MICHIGAN CITY, INDIANA 46360, U.S.A. Fax: 219/872-9057 e-mail: [email protected]
SPECIFICATIONS
Range:
K: -328 to 2372°F (-200 to 1300°C);
J: -202 to 1652°F (-130 to 900°C);
T: -328 to 662°F (-200 to 350°C).
Accuracy:
K: ±0.3% of reading + 1°C;
J/T: ±0.1% of reading + 0.7°C.
Display: 4 digit LCD.
Resolution:
K: 0.1°F/C: -328 to 1202°F (-200 to 650°C); 2°F/1°C (others);
Over 1000°C 1°F/C.
J: 0.1°F/C: -202 to 932°F (-130 to 500°C); 2°F/1°C (others);
T: 0.1°F/C: -328 to 662°F (-200 to 350°C).
Temperature Limits: Ambient -4 to 122°F (-20 to 50°C).
Power Requirements: One CR-2032 lithium battery.
Weight: 3.2 oz (91 g).
Agency Approvals: CE.
The Series TP2 Thermocouple Thermometers can accurately measure a large
temperature range for a wide range of applications including food safety
inspection, lab testing, and HVAC. This hand-held thermometer offers three
models that measure the probe temperature, ambient temperature, and relative
humidity. Additional features include a data hold function, high/low audible alarm,
and auto power off. Device includes a K type probe and battery.
FEATURES
1. Auto power off with disable feature (15 minutes).
2. Data hold function freezes readings on display.
3. Complete with type K bead wire temperature probe and CR2032 battery.
4. °C/°F select function.
5. High/low alarm threshold setting is available.
OPERATING INSTRUCTIONS
Please read the manual completely before using this device.
KEY FUNCTION
1. PWR: Turn on/off the meter or holds current readings.
2. MX/MI/AVG: Cycles between minimum, maximum, and average measurement.
3. MODE: Cycles between probe temperature, ambient temperature and humidity
(depending on model) (TP2-20/TP2-30 only), RH (TP2-30 only). Press and hold for
3 seconds to charge the thermocouple type between K, J, and T (depending on
model) (TP2-10/TP2-20 only).
OPERATION
Power On/Off
Before powering on the meter, plug the thermocouple probe into the meter. Press
the PWR button to turn on the meter. It will make a beep sound and the full screen
of LCD icons will briefly show on the display. The meter is now in normal
measurement mode. While the meter is on, press and hold the PWR button to turn
off the meter.
Sleep Mode (Auto Power Off)
The meter will turn off automatically after 15 minutes if no buttons are pressed. To
disable the auto power off function, when the meter is off, press and hold the
MX/MI/AVG button then press the PWR button to turn on the meter. When the LCD
display shows the following, sleep mode is disabled.
Taking Measurement
Make sure you have plugged the K sensor probe in the meter. If the probe is not
plugged in appropriately, the LCD will show “----” on the display.
5
[127.00]
1-27/64
[36.30]
45/64
[18.01]
15/16
[23.91]
Data Hold
Press and release the PWR button to freeze the reading. Press and release the
PWR button shortly again, the meter will return to normal measurement.
Change Mode
Press the MODE button to select probe temperature or ambient, air temperature
(TP2-20 & TP2-30) and probe temperature, ambient air temperature or relative
humidity (TP2-30).
Select Probe Type
Press and hold the MODE button more than 3 seconds to select probe type K/J/T
(TP2-10 & TP2-20).
Note: Please check your probe type before selecting this function to ensure a
correct reading.