Dwyer BV2M - Manual

Series BV2 Two-Piece Ball Valve
Installation, Operating and Maintenance Instructions
H
E
G
F
(K)
(L)
A
D
B
C
SPECIFICATIONS
Size: 1/4˝ - 3˝ NPT.
Material: ASTM A182 GR. CF8M Body and Tlpc;
Reinforced TFE Seats and Seals;
316 SS Ball and Stem;
304 SS Handle and Locknut.
Max. Pressure: 1000 psi (69 bar) WOG; 150 psi (10.3 bar) SWP.
Max. Temp: -40°F(-40°C) to 450°F (232°C).
0°C 50°C 100°C 150°C 200°C
100°F 200°F 300°F 400°F 450°F
1100
1000
900
800
700
600
500
400
300
200
100
0
Pressure Temperature Ratings
Working Temperature (°F)
W
orking Pressure (P
.S.I.G.)
Bulletin F-61
The Series BV2 is the economical choice for quality, stainless steel ball
valves for use in chemical, petrochemical, pulp and paper, and general
applications. Providing excellent corrosion resistance, the Series BV2
body and tailpiece are constructed of CF8M grade investment cast stain-
less steel, while the ball and stem are manufactured from 316 SS.
Reinforced TFE seats and body seals provide broad chemical compati-
bility and bubble tight shutoff to 1000 psi.
The internally loaded blow-out proof stem provides for safety in the event
of overpressure. Full port design allows maximum Cv with minimal pres-
sure drop. Integral actuator mounting pad allows for ease of automation.
Optional locking handle prevents accidental operation. The Series BV2
is available in sizes ranging from 1/4” to 3” NPT.
INSTALLATION
Prior to installation, inspect valve and pipe ends to make sure they are
free from debris. Material trapped inside the valve can cause damage to
the seats and result in leakage. Clean pipe ends and check for proper
threading to prevent damage to valve internals.
Use a PTFE based thread sealant applied to the pipe threads. With valve
in the OPEN position, install pipe. Use a smooth wrench on the hex por-
tion of the valve, not the valve body, to tighten. Use pipe wrenches on
pipe and pipe fittings only.
©Copyright 2010 Dwyer Instruments, Inc. Printed in U.S.A. 2/10 FR# R2-443081-00 Rev. 2
Dimensions are given in inches.
W.E. ANDERSON DIV., DWYER INSTRUMENTS, INC.
P.O. BOX 358 • MICHIGAN CITY, INDIANA 46361 U.S.A.
Phone: 219/879-8000 www.dwyer-inst.com
Fax: 219/872-9057 e-mail: [email protected]
®
OPERATION
These valves are bi-directional and can be installed with flow in either
direction. Rotate the handle 90 degrees counterclockwise to open and
90 degrees clockwise to close. Check to make sure the process media
is compatible with the valve materials. See “Physical Data”. Do not
exceed pressure or temperature maximum ratings.
MAINTENANCE
The Series BV2 is a non-repairable valve. The only maintenance
required is the occasional tightening of the packing gland nut. Over time
some leakage may occur through the stem orifice. If this occurs tighten
the packing gland nut approximately 1/4 turn.
A
2.165
2.165
2.559
2.992
3.465
3.976
4.331
4.882
6.299
6.929 B
1.969
1.969
2.205
2.323
2.717
2.953
3.268
3.622
5.039
5.394 C
4.055
4.055
5.236
5.236
6.024
6.024
7.520
7.520
9.724
9.724 Size
1/4˝
3/8˝
1/2˝
3/4˝
1˝
1-1/4˝
1-1/2˝
2˝
2-1/2˝
3˝ D
1/4˝ NPT
3/8˝ NPT
1/2˝ NPT
3/4˝ NPT
1˝ NPT
1-1/4˝ NPT
1-1/2˝ NPT
2˝ NPT
2-1/2˝ NPT
3˝ NPT E
(2) 3/16-24 UNC
(2) 3/16-24 UNC
(2) 3/16-24 UNC
(2) 3/16-24 UNC
(2) 3/16-24 UNC
(2) 1/4-20 UNC
(2) 1/4-20 UNC
(2) 1/4-20 UNC
(2) 1/4-20 UNC
(2) 1/4-20 UNC F
.500
.500
.500
.882
.882
1.000
1.000
1.000
1.382
1.382 G
.500
.500
.500
.882
.882
1.000
1.000
1.000
1.382
1.382 H
N/A
N/A
N/A
N/A
N/A
N/A
N/A
2.000
2.764
2.764 Cv
8
15
17
27
35
46
80
110
310
360
F-61:Bulletin F-61_BV2 2/10/10 3:24 PM Page 1