Hoyles 6 way driver interface card for MULTIGUARD indicators - Manual

1 2 3 4 5 6 7 8 9 10 11 12 13 14
C
15
D
16
S
ve -
ve -
ve +
ve +
GENERAL
The MULTIGUARD MG020000 and MG02000P are electrically identical. They enable the serial output an MG series
MULTIGUARD annunciator to be used to drive remote devices such as LEDs, Overdoor lights, Low power sounders and
relays etc..
The MG02000P is supplied on a double gang plastic plate to enable it to be fitted externally to the annunciator at a point closer
to the devices it is driving. The pcb can be remove from the plate and fitted inside the MULTIGUARD if desired. To do this the
board edges must be snapped off at the score lines prior to fitting in the annunciator back box.
If the unit is mounted remotely then a five core connection is required +ve -ve Clock, Data & Strobe. This will enable a total of
16 driver outputs. Normally these would be:-
a. 6 outputs to follow the LEDs of the MULTIGUARD
b. 6 outputs which change state on alarm and restore on reset
c. 4 further four outputs:
i. 1 output which follows the integral buzzer
ii 1 output which follows the integral relay
iii 2 spare outputs which are normally spare but can be nominated by software for custom designed equipment.
Each output offers a switched -ve common collector from a NPN Darlington transistor capable of supplying up to 500ma.
Please note that this is subject to a total limit per card of 2A. Note the MG212100 and MG216110 are only able to provide a
maximum of 250ma for external use.
Dwg No:60036:5 Iss 1 Page 1
MULTIGUARD Output Driver Interface
MG020000 & MG02000P
- + X S D C
16 v.a.c
INPUT 16 v.a.c
INPUT
SERIAL
OUTPUT
RELAY
OUTPUT
RELAY
OUTPUT
1 2 3 4 5 6 7 8 9 10 11 12 13 14
C
15
D
16
S
ve -
ve -
ve +
ve +
MG020000
MG02000P
Complies with Council
Directive 89/336/EEC
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 ve - ve +
C D S ve - ve +
MG212XXX
MG216XXX
MG020000
MG02000P
MG020000
MG02000P
MG020000
MG02000P
RLY
RLY
RLY
RLY RLY
RLY
RLY
Un-used
680R
LED
1N4148
diode
These outputs may be used for
relays, LEDs, lamps, or sounders or
a combination to suit the installation.
If the MG020000 is used to drive
relays then a 1N4148 back emf
diode should be fitted across each
relay as shown. (For clarity only one
is shown).
1 2 3 4 5 6 7 8 9 10 11 12 13 14
C
15
D
16
S
ve -
ve -
ve +
ve +
GENERAL
The MULTIGUARD MG020000 and MG02000P are electrically identical. They enable the serial output an MG series
MULTIGUARD annunciator to be used to drive remote devices such as LEDs, Overdoor lights, Low power sounders and
relays etc..
The MG02000P is supplied on a double gang plastic plate to enable it to be fitted externally to the annunciator at a point closer
to the devices it is driving. The pcb can be remove from the plate and fitted inside the MULTIGUARD if desired. To do this the
board edges must be snapped off at the score lines prior to fitting in the annunciator back box.
If the unit is mounted remotely then a five core connection is required +ve -ve Clock, Data & Strobe. This will enable a total of
16 driver outputs. Normally these would be:-
a. 6 outputs to follow the LEDs of the MULTIGUARD
b. 6 outputs which change state on alarm and restore on reset
c. 4 further four outputs:
i. 1 output which follows the integral buzzer
ii 1 output which follows the integral relay
iii 2 spare outputs which are normally spare but can be nominated by software for custom designed equipment.
Each output offers a switched -ve common collector from a NPN Darlington transistor capable of supplying up to 500ma.
Please note that this is subject to a total limit per card of 2A. Note the MG212100 and MG216110 are only able to provide a
maximum of 250ma for external use.
Dwg No:60036:5 Iss 1 Page 1
MULTIGUARD Output Driver Interface
MG020000 & MG02000P
- + X S D C
16 v.a.c
INPUT 16 v.a.c
INPUT
SERIAL
OUTPUT
RELAY
OUTPUT
RELAY
OUTPUT
1 2 3 4 5 6 7 8 9 10 11 12 13 14
C
15
D
16
S
ve -
ve -
ve +
ve +
MG020000
MG02000P
Complies with Council
Directive 89/336/EEC
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 ve - ve +
C D S ve - ve +
MG212XXX
MG216XXX
MG020000
MG02000P
MG020000
MG02000P
MG020000
MG02000P
RLY
RLY
RLY
RLY RLY
RLY
RLY
Un-used
680R
LED
1N4148
diode
These outputs may be used for
relays, LEDs, lamps, or sounders or
a combination to suit the installation.
If the MG020000 is used to drive
relays then a 1N4148 back emf
diode should be fitted across each
relay as shown. (For clarity only one
is shown).
T. 01744 886600 E. [email protected]
F. 01744 886607 W. www.hoyles.com
Hoyles Electronic Developments Ltd
T. 01744 886600 E. [email protected]
F. 01744 886607 W. www.hoyles.com
Hoyles Electronic Developments Ltd